Chime Inoperative
Chime Inoperative
| Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
| Schematic Reference: Audible Warnings Schematics Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems DEFINITION: One or more chime functions are inoperative. |
||||
| 1 | Did you perform the Diagnostic System Check - Vehicle? | - | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
| 2 |
|
- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
| 3 | Is the vehicle equipped with a chime module (UL5)? | - | Go to Step 5 | Go to Step 4 |
| 4 |
|
- | Go to Step 5 | Go to Speakers Inoperative - One or More in Entertainment |
| 5 |
|
- | Go to Step 7 | Go to Step 6 |
| 6 |
|
- | Go to Step 12 | Go to Step 8 |
| 7 |
|
- | Go to Step 13 | Go to Step 10 |
| 8 | Test the signal circuit of the ignition key alarm switch for an open, for a high resistance, or for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 9 |
| 9 | Test the ground circuit of the ignition key alarm switch for an open or for a high resistance. Refer Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 14 |
| 10 | Test the signal circuit of the driver door ajar switch for an open, for a high resistance, or for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 11 |
| 11 | Test the ground circuit of the driver door ajar switch for an open or for a high resistance. Refer to Circuit Testing
and Wiring Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 15 |
| 12 | Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 16 |
| 13 | Inspect for poor connections at the harness connector of the driver door ajar switch. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 17 |
| 14 | Inspect for poor connections at the harness connector of the ignition key alarm switch. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 18 |
| 15 | Inspect for poor connections at the harness connector of the chime module. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
in Wiring Systems. Did you find and correct the condition? |
- | Go to Step 20 | Go to Step 19 |
| 16 | Replace the BCM. Refer to Control Module References
in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? |
- | Go to Step 20 | - |
| 17 | Replace the driver door ajar switch. Refer to Lock Replacement - Front Door
in Doors. Did you complete the replacement? |
- | Go to Step 20 | - |
| 18 | Replace the ignition key alarm switch. Refer to Ignition Switch Replacement
in Steering Wheel and Column. Did you complete the replacement? |
- | Go to Step 20 | - |
| 19 | Replace the chime module. Refer to Control Module References
in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? |
- | Go to Step 20 | - |
| 20 | Operate the system in order to verify the repair. Did you correct the condition? |
- | System OK | Go to Step 2 |