LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1657 (Lighting Systems) >> Diagnostic Information and Procedures >> DTC B2585 >> Test Description

Test Description

WARNING: This page is about a different car, the 2002 Oldsmobile Bravada, 2002 GMC Envoy XL, 2002 GMC Envoy, and 2002 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Listen for an audible click when the park lamp relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
  2. 3:  Tests for voltage at the coil side of the park lamp relay.
  3. 4:  Verifies that the body control module (BCM) is providing ground to the park lamp relay.
  4. 5:  Tests if ground is constantly being applied to the park lamp relay.
  5. 6:  Tests if there is opposing voltage present or an open park lamp relay control circuit.
  6. 12:  After replacement of the BCM you must calibrate the new module for proper operation.
DTC B2585

Step Action Yes No
Schematic Reference:  Exterior Lights Schematics  
1 Did you perform the Lighting Systems Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Lighting Systems 
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the park lamp relay ON and OFF.
Does the park lamp relay turn ON and OFF with each command?		 Go to TESTING FOR INTERMITTENT CONDITIONS AND POOR CONNECTIONS in Wiring Systems Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the park lamp relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the battery positive voltage circuit of the park lamp relay with a test lamp that is connected to a good ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 10 
4 
  1. Connect a test lamp between the control circuit of the park lamp relay and the battery positive voltage circuit of the park lamp relay.
  2. With a scan tool, command the park lamp relay ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 8  Go to Step 5 
5  Does the test lamp remain illuminated with each command? Go to Step 7  Go to Step 6 
6  Test the control circuit of the park lamp relay for a short to voltage or an open. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
7 Test the control circuit of the park lamp relay for a short to ground. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
8 Inspect for poor connections at the park lamp relay. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 11 
9 Inspect for poor connections at the harness connector of the BCM. Refer to CIRCUIT TESTING and WIRING REPAIRS in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
10 Repair the battery positive voltage circuit of the park lamp relay. Refer to WIRING REPAIRS in Wiring Systems.
Did you complete the repair?		 Go to Step 13  -
11 Replace the park lamp relay. Refer to Park Lamp Relay Replacement .
Did you complete the replacement?		 Go to Step 13  -
12 
IMPORTANT: Perform the setup procedure for the BCM.
Replace the body control module (BCM). Refer to BODY CONTROL MODULE REPLACEMENT in Body Control System.Did you complete the replacement?		 Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals