LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Blazer 4D Utility, 4WD, Part Time >> Repair and Diagnosis >> External Pages >> Different car >> Section 1395 (Seat System) >> Diagnostic Information and Procedures >> DTC B2425 or B2430: Seat Heater Circuit >> Diagnostic Aids

Diagnostic Aids

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2004 Oldsmobile Bravada, 2004 GMC Envoy XUV, 2004 GMC Envoy XL, 2004 GMC Envoy, and 2004 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.

If the DTC is only found in history, the fault may be intermittent. Refer toTesting for Intermittent Conditions and Poor Connections in Wiring Systems.

DTC B2425 or B2430 Diagnostic Test

Step Action Yes No
Schematic Reference: Driver Seat Schematics , Passenger Seat Schematics 
Connector End View Reference: Power Seat Systems Connector End Views 
1 Did you perform the Power Seat Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Power Seat Systems 
2
  1. Start the engine.
  2. Attempt to operate the heated seat system in the back only and back and cushion heating modes.
Does the heated seat system operate normally?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3
  1. Turn OFF the ignition.
  2. Disconnect the seat module connectors C3 and C4.
  3. Turn ON the ignition.
  4. Connect a test lamp from the seat cushion heater element control circuit terminal in the harness connector C4 to ground.
Does the test lamp illuminate?		 Go to Step 7  Go to Step 4 
4 Connect a test lamp from the seat back heater element control circuit terminal in the harness connector C4 to ground.
Does the test lamp illuminate?		 Go to Step 8  Go to Step 5 
5 Connect a test lamp from battery voltage to the seat cushion heater element control circuit terminal in the harness connector C4.
Does the test lamp illuminate?		 Go to Step 9  Go to Step 6 
6 Connect a test lamp from battery voltage to the seat back heater element control circuit terminal in the harness connector C4.
Does the test lamp illuminate?		 Go to Step 10  Go to Step 11 
7 Repair the seat cushion heater element voltage supply or ground circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Is the repair complete?		 Go to Step 13  -
8 Repair the seat back heater element voltage supply or ground circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Is the repair complete?		 Go to Step 13  -
9 Repair the seat cushion heater element voltage supply or ground circuit for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Is the repair complete?		 Go to Step 13  -
10 Repair the seat back heater element voltage supply or ground circuit for a short to ground. Refer to Circuit Testing and toWiring Repairs in Wiring Systems.
Is the repair complete?		 Go to Step 13  -
11 Inspect for poor connections at the seat module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
12 Replace the seat module. Refer to Memory Seat Control Module Replacement .
Is the repair complete?		 Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the system within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals