Selection of Crankshaft Bearing
WARNING: This page is about a different variant/trim than selected.
NOTE:
- In case of mixed class selection, the thicker bearing must be mounted as shown below.
- X / Z: Z = Crankshaft Lower Bearing; W = Crankshaft Upper Bearing
- X / X: X = Crankshaft Lower Bearing; X = Crankshaft Upper Bearing
| Crankshaft Bearing Bore Diameter | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| - | A | B | C | D | E | F | G | ||
| - | 56.021 mm (2.206 in) | 56.022 mm (2.206 in) | 56.023 mm (2.206 in) | 56.024 mm (2.206 in) | 56.025 mm (2.206 in) | 56.026 mm (2.206 in) | 56.027 mm (2.206 in) | ||
| Crankshaft Bearing Journal Diameter | A | 50.992 mm (2.008 in) | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z |
| B | 50.993 mm (2.008 in) | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | |
| C | 50.994 mm (2.008 in) | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | |
| D | 50.995 mm (2.008 in) | X / X | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | |
| E | 50.996 mm (2.008 in) | X / X | X / X | X / X | X / X | X / Z | X / Z | X / Z | |
| F | 50.997 mm (2.008 in) | X / X | X / X | X / X | X / X | X / X | X / X | X / X | |
| G | 48.998 mm (1.929 in) | X / X | X / X | X / X | X / X | X / X | X / X | X / X | |
| H | 50.999 mm (2.008 in) | X / X | X / X | X / X | X / X | X / X | X / X | X / X | |
| J | 51.000 mm (2.008 in) | W / X | X / X | X / X | X / X | X / X | X / X | X / X | |
| K | 51.001 mm (2.008 in) | W / X | W / X | W / X | W / X | X / X | X / X | X / X | |
| L | 51.002 mm (2.008 in) | W / X | W / X | W / X | W / X | W / X | W / X | W / X | |
| M | 51.003 mm (2.008 in) | W / X | W / X | W / X | W / X | W / X | W / X | W / X | |
| N | 51.004 mm (2.008 in) | W / X | W / X | W / X | W / X | W / X | W / X | W / X | |
| P | 51.005 mm (2.008 in) | W / W | W / X | W / X | W / X | W / X | W / X | W / X | |
| R | 51.006 mm (2.008 in) | W / W | W / W | W / W | W / W | W / X | W / X | W / X | |
| S | 51.007 mm (2.008 in) | W / W | W / W | W / W | W / W | W / W | W / W | W / W | |
| T | 51.008 mm (2.008 in) | W / W | W / W | W / W | W / W | W / W | W / W | W / W | |
| Crankshaft Bearing Bore Diameter | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| - | H | J | K | L | M | N | P | R | ||
| - | 56.028 mm (2.206 in) | 56.029 mm (2.206 in) | 56.030 mm (2.206 in) | 56.031 mm (2.206 in) | 56.032 mm (2.206 in) | 56.033 mm (2.206 in) | 56.034 mm (2.206 in) | 56.035 mm (2.206 in) | ||
| Crankshaft Bearing Journal Diameter | A | 50.992 mm (2.008 in) | X / Z | Z / Z | Z / Z | Z / Z | Z / Z | Z / Z | Z / Z | Z / Z |
| B | 50.993 mm (2.008 in) | X / Z | X / Z | X / Z | Z / Z | Z / Z | Z / Z | Z / Z | Z / Z | |
| C | 50.994 mm (2.008 in) | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | Z / Z | |
| D | 50.995 mm (2.008 in) | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | |
| E | 50.996 mm (2.008 in) | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | |
| F | 50.997 mm (2.008 in) | X / X | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | X / Z | |
| G | 48.998 mm (1.929 in) | X / X | X / X | X / X | X / X | X / Z | X / Z | X / Z | X / Z | |
| H | 50.999 mm (2.008 in) | X / X | X / X | X / X | X / X | X / X | X / X | X / X | X / Z | |
| J | 51.000 mm (2.008 in) | X / X | X / X | X / X | X / X | X / X | X / X | X / X | X / X | |
| K | 51.001 mm (2.008 in) | X / X | X / X | X / X | X / X | X / X | X / X | X / X | X / X | |
| L | 51.002 mm (2.008 in) | W / X | X / X | X / X | X / X | X / X | X / X | X / X | X / X | |
| M | 51.003 mm (2.008 in) | W / X | W / X | W / X | W / X | X / X | X / X | X / X | X / X | |
| N | 51.004 mm (2.008 in) | W / X | W / X | W / X | W / X | W / X | W / X | W / X | X / X | |
| P | 51.005 mm (2.008 in) | W / X | W / X | W / X | W / X | W / X | W / X | W / X | W / X | |
| R | 51.006 mm (2.008 in) | W / X | W / X | W / X | W / X | W / X | W / X | W / X | W / X | |
| S | 51.007 mm (2.008 in) | W / W | W / X | W / X | W / X | W / X | W / X | W / X | W / X | |
| T | 51.008 mm (2.008 in) | W / W | W / W | W / W | W / W | W / X | W / X | W / X | W / X | |
For example: Crankshaft Bearing Bore Diameter is 53.796 mm and Crankshaft bearing journal diameter is 48.998 mm.
Use for the crankshaft lower bearing with the ID "X" and the crankshaft upper bearing with the "W".