Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of GENERAL MOTORS COMPANY

Apply Structural foam 3M™ NVH Dampening Material or equivalent to the front compartment side rail baffle (1).
Courtesy of GENERAL MOTORS COMPANY

Front Fender- Left Side - Install
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Refer to Fastener Caution .

Front Fender Bolt (1) - Install and tighten [6x] - Fastener Specifications
Front Fender Nut (2) - Install and tighten - Fastener Specifications
Remove the double layer of masking tape from the windshield.
Courtesy of GENERAL MOTORS COMPANY

Front Fender Bolt (1) - Install and tighten [2x] - Fastener Specifications
Headlamp Bolt (2) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Position the rocker panel molding (2) to the vehicle and seat the upper rocker panel molding retainers (1) into the body side outer panel.
Seat the lower rocker panel molding retainers (1) into the body side outer panel.
Courtesy of GENERAL MOTORS COMPANY

Position the rear wheelhouse liner (4) to its original location.
Rear Wheelhouse Liner Retainer (3) - Install
Rear Tire Front Air Deflector (2) - Install
Rear Tire Front Air Deflector Bolt (1) - Install and tighten [3x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Guide (3) - Install
Front Bumper Fascia Guide Bolt (2) - Install and tighten [2x] - Fastener Specifications
Headlamp Bolt (1) - Install - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia (1) - Install - Front Bumper Fascia Removal and Installation (without Blackwing) , or Front Bumper Fascia Removal and Installation (with Blackwing) , or Front Bumper Fascia Removal and Installation (with Blackwing CFV, CFZ)
Courtesy of GENERAL MOTORS COMPANY

Front Fender Insulator (2) - Install
Front Fender Insulator Retainer (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Front Wheelhouse Liner (3) - Install
Front Wheelhouse Liner Retainer (2) - Install [4x]
Front Wheelhouse Liner Screw (1) - Install and tighten [7x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Engine Front Splash Shield (3) - Install
Engine Front Splash Shield Screw (2) - Install and tighten [5x] - Fastener Specifications
Push Pin (1) - Install
If equipped with RWD:
Courtesy of GENERAL MOTORS COMPANY

Engine Front Splash Shield (3) - Install
Push Pin (2) - Install [2x]
Engine Front Splash Shield Screw (1) - Install and tighten [5x] - Fastener Specifications
Install the tire and wheel assembly. Tire and Wheel Removal and Installation
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [5x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Bolt (1) - Install and tighten [4x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Compartment Side Sight Shield (2) - Install
Front Compartment Side Sight Shield Retainer (1) - Install [3x]
Courtesy of GENERAL MOTORS COMPANY

Air Inlet Grille Panel Extension- Outer (2) - Install
Air Inlet Grille Panel Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Hood Rear Outer Air Inlet Seal (2) - Install
Hood Rear Outer Air Inlet Seal Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Install the air inlet grille panel extension (1).
Remove the masking tape.
Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.