Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of GENERAL MOTORS COMPANY

Front Bumper Energy Absorber (1) Install
Install the wiring harness retainers.
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Refer to Fastener Caution .

Front Bumper Fascia Energy Absorber Bolt (1) - Install and tighten [2x] - Fastener Specifications
Front Compartment Front Panel Bolt (2) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Energy Absorber Bolt (1) - Install and tighten [3x] - Fastener Specifications
Front Compartment Front Panel Bolt (1) - Install and tighten [3x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Charge Air Cooler Bracket (1) - Install
Charge Air Cooler Bracket Bolt (2) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Radiator Outlet Hose (2) - Install
Radiator Outlet Hose Clamp (1) - Install - Hose Clamp Replacement Guidelines - Spring Type
Courtesy of GENERAL MOTORS COMPANY

Intake Air Duct (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Radiator Air Front Upper Baffle (2) - Install
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Assembly (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Bolt (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Air Cleaner Outlet Duct (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Position the engine auxiliary radiator assembly (1) to the vehicle.
Courtesy of GENERAL MOTORS COMPANY

Charge Air Cooler Bracket Bolt (1) - Install and tighten [3x] - Fastener Specifications
Charge Air Cooler Upper Bracket Nut (2) - Tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Auxiliary Radiator Front Duct (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Auxiliary Radiator Duct Retainer (1) - Install [2x]
Courtesy of GENERAL MOTORS COMPANY

Auxiliary Radiator Duct Retainer (1) - Install [3x]
Remove the support and lower the vehicle.
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Impact Bar (2) - Install
Front Bumper Impact Bar Bolt (1) - Install and tighten [8x] - Fastener Specifications
Install the wiring harness and the 5 baffle retainers.
Courtesy of GENERAL MOTORS COMPANY

Horn (2) - Install [2x]
Horn Bolt (1) - Install and tighten [2x] - Fastener Specifications
Connect the electrical connectors.
Courtesy of GENERAL MOTORS COMPANY

Front End Sheet Metal Cross Brace- Right Side (2) - Install
Front End Sheet Metal Cross Brace Bolt (1) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Support Brace (2) - Install
Front Bumper Fascia Support Brace Bolt (1) - Install and tighten [3x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
The front bumper fascia will rest in place by guides on the center support upper structure.

With the aid of an assistant install the front bumper fascia. (1)
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Center Air Deflector Retainer (3) - Install [2x]
Front Bumper Fascia Center Air Deflector Bolt (2) - Install and tighten [5x] - Fastener Specifications
Front Bumper Fascia Center Air Deflector Screw (1) - Install and tighten [9x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Install the left side of the front bumper fascia (1) to the front bumper fascia guide (2) and the front headlamp (3).
Courtesy of GENERAL MOTORS COMPANY

Connect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

Install the right side of the front bumper fascia (1) to the front bumper fascia guide (2) and the front headlamp (3).
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Bolt (1) - Install and tighten [6x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Install and tighten the left side upper front bumper fascia bolt (2). Fastener Specifications
Front Wheelhouse Liner (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Install and tighten the right side upper front bumper fascia bolt (2). Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Bolt- Right Side (3) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Install the right front wheelhouse liners (3).
Front Wheelhouse Liner Retainer (2) - Install [4x]
Front Wheelhouse Liner Bolt (1) - Install and tighten [7x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [3x] - Fastener Specifications
Front Bumper Fascia Bolt (2) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY
NOTE:
- Left side shown, right side similar.
- Quantity of fasteners may vary based on option content.
- Components removed for graphic clarity.
Engine Front Splash Shield (3) - Install
Engine Front Splash Shield Retainer (2) - Install [2x]
Engine Front Splash Shield Bolt (1) - Install and tighten [5x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY
NOTE:
- Left side shown, right side similar.
- Quantity of fasteners may vary based on option content.
Front Tire Front Air Deflector (2) - Install
Front Tire Front Air Deflector Bolt (1) - Install and tighten [4x] - Fastener Specifications
Install the tire and wheel assembly. Tire and Wheel Removal and Installation
Fill the cooling system to the proper level. Cooling System Draining and Filling (LSY GE 47716) , or Cooling System Draining and Filling (LSY Static Fill) , or Cooling System Draining and Filling (LSY with V03 Static Fill) , or Cooling System Draining and Filling (L3B Static Fill) , or Cooling System Draining and Filling (L3B GE 47716) , or Cooling System Draining and Filling (LSY with V03 GE 47716) , or Cooling System Draining and Filling (LF4 Static Fill) , or Cooling System Draining and Filling (LF4 GE 47716)
Start the engine and check for coolant leaks.