LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 58 (Hydraulic Brakes - Repair Instructions) >> Repair Instructions >> Rear Brake Front Pipe Replacement - Left Side (Rear Brake Rear Pipe) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5523138

    Maneuver the rear brake rear pipe (2) into the vehicle.

  2. Remove the cap from the rear brake rear pipe outlet.
  3. Remove the plug from the brake pipe union inlet.
    4. CAUTION:

    Refer to Fastener Caution .

  4. Rear Brake Pipe Fitting (3) - Install and tighten - Fastener Specifications
  5. Secure the rear brake rear pipe into the retainer (1).
  6. Remove the support and lower the vehicle.
  7. GM5523140

    Secure the rear brake rear pipe into the 3 retainers (1).

  8. GM5493276

    Brake Master Cylinder (1) - Install

  9. GM5324653

    Brake Master Cylinder Nut (1) - Install and tighten [2x] - Fastener Specifications

  10. GM5486241

    Install a NEW brake pedal retainer (1) to the brake master cylinder push rod.

  11. Engage the brake pedal (2) to the brake pedal retainer (1) by pushing inwards.
  12. Ensure the locking tabs on the brake pedal retainer are fully engaged in the brake pedal (2) and the retainer is attached securely to the brake master cylinder push rod.
  13. Connect the front floor courtesy lamp electrical connector.
  14. GM5310879

    Instrument Panel Lower Trim Panel Insulator (1) - Install

  15. GM5310878

    Install the tabs into the instrument panel lower trim panel insulator (1).

  16. GM5310877

    Instrument Panel Lower Trim Panel Insulator Retainer (1) - Install

  17. Instrument Panel Insulator Bolt (2) - Install and tighten [2x] - Fastener Specifications
  18. Instrument Panel Insulator Nut (3) - Install and tighten [2x] - Fastener Specifications
  19. GM5300282

    Attach the hood primary latch release cable end retainer to the hood primary latch release cable handle (1).

  20. Remove the caps from the 4 brake front pipe inlets.
  21. GM5488446

    Front Brake Pipe Nut (2) - Install and tighten [2x] - Fastener Specifications

  22. Rear Brake Pipe Nut (1) - Install and tighten [2x] - Fastener Specifications
  23. GM5324655

    Electrical Connector (1) @ Brake System Control Module - Connect

  24. GM5491702

    Electrical Connector (1) @ Brake Fluid Level Sensor - Connect

  25. GM5492906

    Front End Sheet Metal Diagonal Brace (2) - Install

  26. Front End Sheet Metal Diagonal Brace Bolt (3) - Install and tighten [2x] - Fastener Specifications
  27. Front End Sheet Metal Diagonal Brace Nut (1) - Install and tighten - Fastener Specifications
  28. GM5422044

    Plenum Front Panel (1) - Install

  29. GM5422041

    Install the forward lamp wiring harness extension (3) into the plenum front panel.

  30. Plenum Front Panel Bolt (1) - Install and tighten [4x] - Fastener Specifications
  31. Plenum Front Panel Nut (2) - Install and tighten [3x] - Fastener Specifications
  32. GM5422039

    Install the forward lamp wiring harness extension (3) into the plenum front panel.

  33. Plenum Front Panel Nut (1) - Install and tighten [3x] - Fastener Specifications
  34. Plenum Front Panel Bolt (2) - Install and tighten [3x] - Fastener Specifications
  35. Connect the electrical connectors.
  36. GM5499583

    Air Inlet Deflector Water Deflector (1) - Install

  37. GM5499581

    Air Inlet Deflector Water Deflector Retainer (1) - Install [2x]

  38. GM5420344

    Install the windshield wiper system module (2) in the vehicle.

  39. Windshield Wiper System Module Bolt (1) - Install and tighten [2x] - Fastener Specifications
  40. Connect the windshield wiper motor electrical connector.
  41. GM5420286

    Windshield Wiper System Module Shield (1) - Install

  42. GM5417442

    Air Inlet Grille Panel (2) - Install

  43. Install the air inlet grille panel (2) between both hood hinges.
  44. Connect the windshield washer nozzle hose to the windshield washer pump hose.
  45. Air Inlet Grille Panel Retainer (1) - Install [6x]
  46. GM5421990

    Install the front compartment side sight shields (2) to both sides.

  47. Install the front compartment side sight shield retainers (1) to both sides.
  48. GM5421986

    Install the hood rear outer air inlet seals (2) to both sides.

  49. Install the hood rear outer air inlet seal retainers (1) to both sides.
  50. GM5417116

    Install the air inlet grille panel extensions (1).

  51. Remove the masking tape from the body around the top edges of the air inlet grille panel extensions (1).
  52. Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
  53. GM5325063
  54. Clean the windshield wiper transmission pivot shaft splines with a soft wire brush before installing the windshield wiper arms (3).
  55. Position the windshield wiper arms (3) on the windshield wiper transmission pivot shafts.
  56. Windshield Wiper Arm Nut (2) - Install and tighten [2x] - Fastener Specifications
  57. Windshield Wiper Arm Finish Cap (1) - Install [2x]
  58. Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
  59. Bleed the brake system. Hydraulic Brake System Bleeding (JE5, J6G) , or Hydraulic Brake System Bleeding (J55) 
  60. Check for brake system leaks.
  61. GM5416557

    If required, realign the windshield wipers to their respective alignment circles (1) on the windshield.

  62. Lubricate the windshield with clean washer fluid.
  63. Run the windshield wipers for two complete cycles then turn off the windshield wipers.
  64. Ensure the windshield wipers are in the full park position.
  65. Inspect the windshield wipers for proper position to the alignment circles (1) on the windshield.
scientia non olet · About LEMON Manuals