LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 58 (Hydraulic Brakes - Repair Instructions) >> Repair Instructions >> Hydraulic Brake System Bleeding (J55) >> Bleeding a Single Rear Hydraulic Brake Circuit

Bleeding a Single Rear Hydraulic Brake Circuit

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect brake fluid level sensor
  2. Use Global Diagnostic System (GDS) to deactivate brake boost system.
  3. Place a clean shop cloth beneath the brake master cylinder to prevent brake fluid spills.
  4. Clean the outside of the reservoir on and around the reservoir cap prior to removing the cap and diaphragm.
    5. NOTE:

    The pressure bleeding equipment must be the diaphragm type. The rubber diaphragm between the air supply and the brake fluid prevents air, moisture, oil, and other contaminants from entering the hydraulic system.

  5. Fill the brake master cylinder reservoir with GM approved brake fluid from a clean, sealed brake fluid container. Ensure that the brake master cylinder reservoir remains at least half-full during this bleeding procedure. Add fluid as needed to maintain the proper level. Brake Master Cylinder Reservoir Filling 
  6. Check the brake fluid level in the CH-29532-A  Pressure Brake Bleeder. Add GM approved brake fluid from a clean, sealed brake fluid container as necessary to bring the level to approximately the half-full point. Adhesives, Fluids, Lubricants, and Sealers
  7. Install the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter to the brake master cylinder reservoir.
  8. Connect the CH-29532-A  Pressure Brake Bleeder, to the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter.
  9. Charge the CH-29532-A  Pressure Brake Bleeder, air tank to 207 - 310 kPa (30 - 45 psi)  .
  10. Open the CH-29532-A  Pressure Brake Bleeder, fluid tank valve to allow pressurized brake fluid to enter the brake system.
  11. Wait approximately 30 seconds, then inspect the entire hydraulic brake system in order to ensure that there are no existing external brake fluid leaks. Any brake fluid leaks identified require repair prior to completing this procedure. Brake System External Leak Inspection
  12. Install a proper box-end wrench onto the wheel hydraulic circuit bleeder valve which has been serviced.
  13. Install a transparent hose over the end of the bleeder valve.
  14. Submerge the open end of the transparent hose into a transparent container partially filled with GM approved brake fluid from a clean, sealed brake fluid container. Adhesives, Fluids, Lubricants, and Sealers
  15. Loosen the bleeder valve to purge air from the wheel hydraulic circuit.
  16. Allow fluid to flow until air bubbles stop flowing from the bleeder.
  17. Cycle the park brake ON and OFF after opening the bleeder valve on the rear calipers.
    18. CAUTION:

    Refer to Fastener Caution .

  18. After all air has been purged from the hydraulic circuit, tighten the bleeder valve to the necessary torque specification and install the dust cap. Fastener Specifications
    19. NOTE:

    The brake reservoir may have residual pressure after the bleeding operation is complete. Wrap a clean shop towel around the bleeder adapter and all hose connections before disconnecting the pressure bleeding equipment to prevent brake fluid from contacting and damaging vehicle components and painted surfaces

  19. Close the CH-29532-A  Pressure Brake Bleeder, fluid tank valve, then disconnect the CH-29532-A  Pressure Brake Bleeder, from the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter.
  20. Remove the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter from the brake master cylinder reservoir.
  21. Fill the brake master cylinder reservoir to the maximum-fill level with GM approved brake fluid from a clean, sealed brake fluid container. Adhesives, Fluids, Lubricants, and Sealers
  22. Inspect the brake system for external leaks. Brake System External Leak Inspection
  23. Run the GDS - Brake Hydraulic Test, if it fails, perform the Bleeding the Complete Brake Hydraulic System procedure.
  24. Connect the brake fluid level sensor
  25. Turn the ignition ON, with the engine OFF. Check to see if the brake system warning lamp remains illuminated.
  26. Inspect the brake system for external leaks. Brake System External Leak Inspection
    27. NOTE:

    DO NOT allow the vehicle to be driven until it is diagnosed and repaired.

  27. If the brake system warning lamp remains illuminated, go to Diagnostic Starting Point - Vehicle .
scientia non olet · About LEMON Manuals