LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 58 (Hydraulic Brakes - Repair Instructions) >> Repair Instructions >> Brake Pedal Assembly Replacement (without MG9) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5486242

    Using an assistant to reposition the brake master cylinder - with power brake booster and electronic brake control module, install the brake pedal assembly (3).

    2. CAUTION:

    Refer to Fastener Caution .

  2. Brake Master Cylinder Nut (2) - Install and tighten [2x] - Fastener Specifications
  3. Brake Pedal Nut (1) - Install and tighten [2x] - Fastener Specifications
  4. GM5880985

    Engage the brake pedal (1) to the brake master cylinder push rod by pushing inwards.

  5. Ensure the brake pedal retainer is secured by lightly pulling rearward on the brake pedal (1).
  6. GM5333075

    Brake Pedal Position Sensor Electrical Connector (2) - Connect

  7. Retainer (1) - Secure [2x]
  8. GM5644434

    Reposition the instrument panel outer air outlet inner duct (1).

  9. Air Distributor Duct Bolt (2) - Install and tighten - Fastener Specifications
  10. GM5454443

    Serial Data Gateway Bracket (2) - Install

  11. Serial Data Gateway Module Bracket Bolt (1) - Tighten [2x] - Fastener Specifications
  12. Connect and position the wiring harness.
  13. GM5454224
    NOTE:

    Typical wiring harness shown. Individual wiring harnesses may differ based on option content.

    Connect the electrical connectors. (1)

  14. Floor Front Air Outlet Duct Bolt (1) - Install and tighten - Fastener Specifications
  15. GM5454049

    Instrument Panel Knee Bolster Deflector (2) - Install

  16. Instrument Panel Tie Bar Brace Bolt (1) - Install and tighten [3x] - Fastener Specifications
  17. GM5325852

    Floor Front Air Outlet Duct - Left Side Outer (2) - Install

  18. GM5446428

    Connect and position the wiring harness.

  19. Instrument Panel Knee Bolster (1) - Install
  20. GM5446424

    Data Link Connector Bolt (1) - Install and tighten [2x] - Fastener Specifications

  21. Instrument Panel Knee Bolster Bolt (2) - Install and tighten [3x] - Fastener Specifications
  22. Connect the electrical connector.
  23. GM5433957

    Connect the electrical connector.

  24. Instrument Panel Center Trim Pad (1) - Install
  25. Return the steering column to its original position.
  26. GM5310879

    Connect the electrical connector.

  27. Instrument Panel Lower Trim Panel Insulator (1) - Install
  28. GM5310878

    Install the tabs into the instrument panel lower trim panel insulator (1).

  29. GM5310877

    Instrument Panel Lower Trim Panel Insulator Retainer (1) - Install

  30. Instrument Panel Insulator Bolt (2) - Install and tighten [2x] - Fastener Specifications
  31. Instrument Panel Insulator Nut (3) - Install and tighten [2x] - Fastener Specifications
  32. GM5300282

    Attach the hood primary latch release cable end retainer to the hood primary latch release cable handle (1).

  33. GM5421735

    Instrument Panel Outer Trim Cover - Left Side (1) - Install

  34. GM5443235

    Connect the electrical connector.

  35. Instrument Panel Lower Airbag - Driver Side (2) - Install
  36. Instrument Panel Lower Airbag Nut (1) - Install and tighten [2x] - Fastener Specifications
  37. Enable the SIR System. SIR Disabling and Enabling .
  38. Calibrate the brake pedal position sensor. Brake Pedal Position Sensor Calibration
scientia non olet · About LEMON Manuals