LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 158 (Engine Mechanical - 2.7L (L3B) - Repair Instructions (1 Of 3)) >> Repair Instructions >> Engine Mount Replacement - Left Side (AWD) >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5517340

    Engine Mount (1) - Install

  2. Lower the engine.
  3. GM5517339

    Electrical Connector (1) - Connect

  4. GM5317837

    Front Crossmember Brace (3) - Install

    5. CAUTION:

    Refer to Fastener Caution

  5. Front Crossmember Brace Bolt (1) - Install and tighten [4x] - Fastener Specifications
  6. Front Crossmember Brace Nut (2) - Install and tighten - Fastener Specifications
  7. GM5399497

    Push Pin (1) @ Front Wheelhouse Liner (2) - Install

  8. GM5399464

    { If equipped } Front Crossmember Brace (2) - Install

  9. { If equipped } Front Crossmember Brace Nut (1) - Install and tighten [4x] - Fastener Specifications
  10. GM5398004

    Front Compartment Air Deflector - (1) Install

  11. GM5398001

    Front Compartment Air Deflector Bolt (1) - Install and tighten [6x] - Fastener Specifications

  12. GM5398000

    Front Wheelhouse Liner Bolt (3) - Install and tighten - Fastener Specifications

  13. Push Pin (2) - Install and tighten
  14. Engine Front Splash Shield Bolt (1) - Install and tighten - Fastener Specifications
  15. GM5397993

    Front Wheelhouse Liner Bolt (1) - Install and tighten - Fastener Specifications

  16. Push Pin (2) - Install
  17. Engine Front Splash Shield Bolt (3) - Install and tighten - Fastener Specifications
  18. GM5397986

    Front Bumper Fascia Center Air Deflector Bolt (1) - Install and tighten [5x] - Fastener Specifications

  19. Push Pin (2) - Install [2x]
  20. Lower the vehicle.
  21. GM5517338

    Engine Mount Nut (2) - Install and tighten - Fastener Specifications

    22. CAUTION:

    Refer to Torque-to-Yield Fastener Caution .

  22. Engine Mount Bolt (1) - Install NEW and tighten [2x] - Fastener Specifications
  23. Remove the engine support fixture. Engine Support Fixture 
  24. GM5396237

    Engine Oil Cooler Coolant Outlet Hose (2) - Install

  25. Hose Clamp (1) - Engage [2x] - Hose Clamp Replacement Guidelines - Spring Type
  26. GM5396233

    Automatic Transmission Fluid Cooling Heat Exchanger Outlet Hose (2) @ Engine Oil Cooler Coolant Outlet Hose - Install

  27. Hose Clamp (1) - Engage - Hose Clamp Replacement Guidelines - Spring Type
  28. GM5517337

    Radiator Inlet Hose (3) - Install

  29. Radiator Inlet Hose Clip (2) @ Radiator Inlet Hose Bracket - Install
  30. Radiator Inlet Hose Clamp (1) - Engage [2x] - Hose Clamp Replacement Guidelines - Spring Type
  31. GM5045008

    Crankcase Vent Passage Seal (4) - Install NEW

  32. Intake Manifold Gasket (3) - Install NEW [4x]
  33. GM5507557

    Intake Manifold (1) - Install

  34. GM5508646
    CAUTION:

    Refer to Fastener Caution .

    Intake Manifold Bolt (1) - Install and tighten [6x] - Fastener Specifications

  35. GM5507451

    Retainer (1) - Install

  36. GM5399157

    Charge Air Cooler Outlet Air Tube (2) @ Throttle Body (3) - Install

  37. Retainer Spring (1) - Engage
  38. GM5517201

    Oil Level Indicator Tube (2) - Install

  39. Oil Level Indicator Tube Bracket Bolt (1) - Install and tighten - Fastener Specifications
  40. GM5507441

    Upper Intake Manifold Cover (1) - Install

  41. GM5507437

    Intake Manifold Cover Stud (2) - Install and tighten [3x] - Fastener Specifications

  42. Intake Manifold Cover Bolt (1) - Install and tighten [2x] - Fastener Specifications
  43. GM5402098

    Evaporative Emission Canister Purge Pump (2) - Install

  44. Evaporative Emission Canister Purge Pump Bolt (1) - Install and tighten [3x] - Fastener Specifications
  45. GM5504108

    Engine Wiring Harness (4) - Reposition

  46. Retainer (3) - Install [4x]
  47. Electrical Connector (2) - Connect [2x]
  48. Engine Wiring Harness Bolt (1) - Install and tighten - Fastener Specifications
  49. GM5509132

    Throttle Body Electrical Connector (1) - Connect

  50. GM5504095

    Radiator Surge Tank Inlet Hose (3) - Reposition

  51. Retainer (2) - Install [3x]
  52. Evaporative Emission Canister Purge Tube (1) - Connect
  53. GM5504092

    Evaporative Emission Pipe (2) - Connect

  54. Fuel Feed Pipe (1) - Connect
  55. GM5456829
    NOTE:

    Ensure the intake manifold cover insulator retainers fully engage the intake manifold cover studs.

    Intake Manifold Cover Insulator (1) - Install

  56. GM5456746

    Intake Manifold Cover Bolt (1) - Install and tighten - Fastener Specifications

  57. GM5432174

    Intake Manifold Cover (1) @ Upper Intake Manifold Bracket (2) - Install

  58. GM5432171

    Push down on the front of the intake manifold cover (2).

  59. Intake Manifold Cover Bolt (1) - Install and tighten [2x] - Fastener Specifications
  60. Install the oil fill cap.
  61. Fill the cooling system. Refer to Cooling System Draining and Filling (L3B Static Fill) , or Cooling System Draining and Filling (L3B GE 47716)
  62. Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
  63. Pressurize the fuel system and inspect for leaks.
  64. Check the cooling system for leaks.
  65. Perform the intake system learned values reset. Intake System Learned Values Reset
  66. Perform the throttle body idle air flow compensation reset. Throttle Body Idle Air Flow Compensation Reset
scientia non olet · About LEMON Manuals