LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 131 (Engine Mechanical - 3.6L (LF4) - Repair Instructions (1 Of 4)) >> Repair Instructions >> Turbocharger Oil Feed Pipe Replacement - Bank 2 >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
  1. GM5875352

    Turbocharger Oil Feed Pipe (3) - Install

    2. NOTE:

    Some components not shown for graphic clarity.

  2. Turbocharger Oil Feed Pipe Washer (2) - Install NEW
    3. CAUTION:

    Refer to Fastener Caution .

  3. Turbocharger Oil Feed Pipe Bolt (1) - Install and tighten - Fastener Specifications
  4. GM5875351
    NOTE:

    Some components not shown for graphic clarity.

    Turbocharger Oil Feed Pipe Fitting Clip (2) - Install

  5. Positive Assurance Cap (1) - Install
  6. GM5869549
    NOTE:

    Some components not shown for graphic clarity.

    Engine Mount Bracket (1) - Install

  7. GM5869547
    CAUTION:

    Refer to Torque-to-Yield Fastener Caution .

    Engine Mount Bracket Bolt (1) - Install NEW and tighten [4x] - Fastener Specifications

  8. GM5867019

    Engine Mount (1) - Install

  9. Lower the engine.
  10. GM5867016

    Engine Mount Nut (2) - Install and tighten - Fastener Specifications

    11. CAUTION:

    Refer to Torque-to-Yield Fastener Caution .

  11. Engine Mount Bolt (1) - Install NEW and tighten [2x] - Fastener Specifications
  12. GM5877068

    Install the front cradle sheer plate (2) between the front bumper fascia center air deflector and the driveline and front suspension cradle and raise into position.

  13. Ensure that the left and right side wheelhouse liners (1) are positioned in place under the front cradle sheer plate (2).
  14. GM5877073

    Front Wheelhouse Liner Bolt (1) - Install and tighten [2x] - Fastener Specifications

  15. GM5877036

    Front Crossmember Brace Bolt (3) - Install and tighten [8x] - Fastener Specifications

  16. Front Cradle Shear Plate Nut (2) - Install and tighten [2x] - Fastener Specifications
  17. Front Cradle Shear Plate Bolt (1) - Install and tighten [4x] - Fastener Specifications
  18. Remove the jack.
  19. GM5862911

    Front Bumper Fascia Air Deflector Retainer (2) - Install

  20. Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [4x] - Fastener Specifications
  21. GM5876696
    NOTE:

    Left side shown, right side similar.

    Front Compartment Air Deflector- Left Side and Right Side (1) - Install

  22. GM5876673
    NOTE:

    Left side shown, right side similar.

    Front Bumper Fascia Lower Stiffener Bolt- Left Side and Right Side (3) - Install and tighten [6x] - Fastener Specifications

  23. Front Compartment Air Deflector Retainer- Left Side and Right Side (2) - Install [2x]
  24. Front Wheelhouse Liner Bolt- Left Side and Right Side (1) - Install and tighten [4x] - Fastener Specifications
  25. Lower the vehicle.
  26. Remove the engine support fixture. Engine Support Fixture
scientia non olet · About LEMON Manuals