LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 Sport, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 116 (Manual Transmission - TREMEC 6-Speed (Mg9) - Repair Instructions - On Vehicle) >> Repair Instructions - On Vehicle >> Manual Transmission Control Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE:

    Before installing the manual transmission control, ensure that the shift shaft it is clean of dirt or lubricants.

  1. Install the manual transmission control to the transmission.
  2. GM5868083Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    The view is for better understanding of component.

    Install the right manual transmission control lever base pin (2).

  3. Install the left manual transmission control lever base pin (2).
  4. GM5868084Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    The view is for better understanding of component.

    Install the manual transmission control lever base pin (2).

  5. Install the 2 manual transmission control lever base pin retainers (1).
  6. Raise the transmission.
  7. GM5867368Courtesy of GENERAL MOTORS COMPANY

    Transmission Mount (2) - Install

    8. NOTE:

    For proper bolt alignment, loosely install all mount bolts prior to tightening to specifications.

  8. Transmission Mount Bolt (1) - Loosely install [2x]
  9. GM5867366Courtesy of GENERAL MOTORS COMPANY

    Transmission Mount Bracket Bolt (1) - Loosely install [4x]

  10. GM5867368Courtesy of GENERAL MOTORS COMPANY
    CAUTION:

    Refer to Fastener Caution .

    Transmission Mount Bolt (1) - Tighten [2x] - Fastener Specifications

  11. GM5867366Courtesy of GENERAL MOTORS COMPANY

    Transmission Mount Bracket Bolt (1) - Tighten [4x] - Fastener Specifications

  12. Remove the jack stand.
  13. GM5867503Courtesy of GENERAL MOTORS COMPANY

    Position the propeller shaft (1) in the vehicle.

  14. GM5863691Courtesy of GENERAL MOTORS COMPANY

    If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:

    1. Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
    2. Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
    15. CAUTION:

    Refer to Fastener Caution .

  15. Install the 2 propeller shaft bearing support bolts (1) and tighten. Fastener Specifications
  16. GM5863695Courtesy of GENERAL MOTORS COMPANY

    Align the reference mark (3) between the propeller shaft flange (1) and the rear axle pinion flange (2).

  17. GM5863697Courtesy of GENERAL MOTORS COMPANY

    If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:

    1. Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
    2. Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  18. Install the 3 rear propeller shaft nuts (2) and 3 the rear propeller shaft bolts (1).
  19. Tighten the 3 the rear propeller shaft bolts (1). Fastener Specifications
  20. GM5867501Courtesy of GENERAL MOTORS COMPANY

    Align the reference mark (2) between the propeller shaft flange (3) and the output flange (1) of the transmission.

  21. GM5867502Courtesy of GENERAL MOTORS COMPANY

    If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:

    1. Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
    2. Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  22. Install the 3 front propeller shaft nuts (1) and the 3 front propeller shaft bolts (2).
  23. Tighten the 3 front propeller shaft bolts (1). Fastener Specifications
  24. GM5334717Courtesy of GENERAL MOTORS COMPANY

    Floor Panel Number 2 Cross Bar Reinforcement (2) - Install

  25. Floor Panel Number 2 Cross Bar Reinforcement Bolt (1) - Install and tighten [4x] - Fastener Specifications
  26. GM5865888Courtesy of GENERAL MOTORS COMPANY

    Exhaust Intermediate Underbody Heat Shield (2) - Install

  27. Exhaust Heat Shield Bolt (1) - Install and tighten [2x] - Fastener Specifications
  28. GM5865329Courtesy of GENERAL MOTORS COMPANY

    Catalytic Converter Gasket (2) - Install NEW

  29. With the aid of an assistant, install the exhaust muffler (1).
  30. GM5865300Courtesy of GENERAL MOTORS COMPANY

    Exhaust Muffler Hanger Bracket Nut (1) - Install and tighten [4x] - Fastener Specifications

  31. GM5865293Courtesy of GENERAL MOTORS COMPANY

    Electrical Connector (1) - Connect

  32. GM5865287Courtesy of GENERAL MOTORS COMPANY

    Electrical Connector (1) - Connect

  33. GM5406632Courtesy of GENERAL MOTORS COMPANY

    Exhaust Muffler (1) @ Exhaust Intermediate Pipe Insulator-Right Side (2) - Install [2x]

  34. GM5406578Courtesy of GENERAL MOTORS COMPANY

    Exhaust Muffler (1) @ Exhaust Intermediate Pipe Insulator-Left Side (2) - Install [2x]

  35. GM5865271Courtesy of GENERAL MOTORS COMPANY

    Exhaust Pipe Clamp (1) - Tighten [2x] - Fastener Specifications

  36. GM5865265Courtesy of GENERAL MOTORS COMPANY

    Catalytic Converter Nut (1) - Install and tighten [2x] - Fastener Specifications

  37. GM5400756Courtesy of GENERAL MOTORS COMPANY

    Floor Panel Reinforcement (2) - Install

  38. Floor Panel Number 4 Cross Bar Reinforcement Bolt (1) - Install and tighten [6x] - Fastener Specifications
  39. GM5854893Courtesy of GENERAL MOTORS COMPANY

    Underbody Rear Air Deflector- Left Side (5) - Install

  40. Transmission Fluid Cooler Pipe Bracket Bolt- Left Side (3) - Install and tighten [2x] - Fastener Specifications
  41. Underbody Rear Air Deflector Nut- Left Side (2) - Install and tighten [5x] - Fastener Specifications
  42. Underbody Front Air Deflector Bolt- Left Side (1) - Install and tighten [6x] - Fastener Specifications
  43. GM5839256Courtesy of GENERAL MOTORS COMPANY

    Underbody Rear Air Deflector- Right Side (5) - Install

  44. Transmission Fluid Cooler Pipe Bracket Bolt- Right Side (3) - Install and tighten [2x] - Fastener Specifications
  45. Underbody Rear Air Deflector Nut- Right Side (2) - Install and tighten [5x] - Fastener Specifications
  46. Underbody Front Air Deflector Bolt- Right Side (1) - Install and tighten [6x] - Fastener Specifications
  47. GM5400642Courtesy of GENERAL MOTORS COMPANY

    Underbody Rear Air Deflector- Right Side (5) - Install

  48. Underbody Rear Air Deflector Nut- Right Side (3) - Install and tighten [3x] - Fastener Specifications
  49. Underbody Rear Air Deflector Bolt- Right Side (2) - Install and tighten [3x] - Fastener Specifications
  50. Underbody Rear Air Deflector Nut- Right Side (4) - Install and tighten [2x] - Fastener Specifications
  51. Rear Wheelhouse Liner Bolt- Right Side (1) - Install and tighten - Fastener Specifications
  52. GM5400553Courtesy of GENERAL MOTORS COMPANY

    Underbody Rear Air Deflector- Left Side (5) - Install

  53. Underbody Rear Air Deflector Nut- Left Side (2) - Install and tighten [3x] - Fastener Specifications
  54. Underbody Rear Air Deflector Bolt- Left Side (3) - Install and tighten [3x] - Fastener Specifications
  55. Underbody Rear Air Deflector Nut- Left Side (4) - Install and tighten [2x] - Fastener Specifications
  56. Rear Wheelhouse Liner Bolt- Left Side (1) - Install and tighten - Fastener Specifications
  57. GM5395705Courtesy of GENERAL MOTORS COMPANY

    Rear Tire Front Air Deflector- Left Side and Right Side (2) - Install [2x]

  58. Rear Tire Front Air Deflector Bolt- Left Side and Right Side (1) - Install and tighten [4x] - Fastener Specifications
  59. GM5868075Courtesy of GENERAL MOTORS COMPANY

    Pull up and outward on the tabs on the closeout boot (1) to clear the body structure.

  60. Install the 4 manual transmission control bracket bolts (1, 2) securing the shift control assembly to the tunnel reinforcement, then tighten. Fastener Specifications
  61. GM5868067Courtesy of GENERAL MOTORS COMPANY

    Install the manual transmission control lever lower boot (1) to the manual transmission control (2).

  62. GM5873426Courtesy of GENERAL MOTORS COMPANY

    Front Floor Console Wiring Harness Extension Harness (1) - Install

  63. GM5873473Courtesy of GENERAL MOTORS COMPANY

    Wireless Charging System Module (2) - Install

  64. Wireless Charging System Module Bolt (1) - Install and tighten [2x] - Fastener Specifications
  65. Connect the electrical connector.
  66. GM5873480Courtesy of GENERAL MOTORS COMPANY

    Vehicle Stability Control System Switch (2) - Install

  67. Auxiliary Multifunction Switch Bolt (1) - Install and tighten [3x] - Fastener Specifications
  68. Connect the electrical connector.
  69. GM5868026Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connector.

  70. Front Floor Console Trim Plate (1) - Install
  71. GM5868061Courtesy of GENERAL MOTORS COMPANY

    If NEW threaded components are being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded components are reused, prepare the threaded components using the following steps:

    1. Remove any loose cured adhesive from the external threads of the components using a lint free cloth.
    2. Thread the cleaned components into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the components. Adhesives, Fluids, Lubricants, and Sealers
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  72. Position the transmission control lever boot and knob assembly (1, 2) on the manual transmission control lever.
  73. Tighten the manual transmission control lever knob bolt (3). Fastener Specifications
  74. Install the manual transmission control lever boot (2) to the console.
  75. Remove the support and lower the vehicle.
  76. Inspect the exhaust system for leaks.
  77. Perform the gear position relearn. Gear Position Sensor Learn 
scientia non olet · About LEMON Manuals