Installation Procedure

WARNING: This page is about a different car, the 2022 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of GENERAL MOTORS COMPANY

Steering Linkage Inner Tie Rod (1) - Install

CAUTION:

Fastener Caution .

Using an appropriate tool, tighten the steering linkage inner tie rod. Fastener Specifications .
Courtesy of GENERAL MOTORS COMPANY

Position a NEW steering gear boot inner clamp (1) on the steering gear boot (2).
Courtesy of GENERAL MOTORS COMPANY

Steering Gear Boot (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Steering Gear Boot Inner Clamp (2) - Tighten-use DT-35910 Drive Axle Boot Clamp Pliers (1)
Courtesy of GENERAL MOTORS COMPANY

Steering Gear Boot Outer Clamp (1) - Install
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Tighten the steering linkage inner tie rod nut (1) during the front toe adjustment procedure.

NOTE:
Some components not shown for graphic clarity.

Install the steering linkage inner tie rod nut (1) until aligned with the previously placed matched mark on the steering linkage inner tie rod.
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Ensure the Outer Tie Rod Boot is not twisted or deformed during assembly. If the boot is twisted or deformed, damage to the boot will occur.

NOTE:
Some components not shown for graphic clarity.

Steering Linkage Outer Tie Rod (1) - Install
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Fastener Caution .

NOTE:
Some components not shown for graphic clarity.

Steering Linkage Outer Tie Rod Nut (1) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Install the front cradle sheer plate (2) between the front bumper fascia center air deflector and the driveline and front suspension cradle and raise into position.
Ensure that the left and right side wheelhouse liners (1) are positioned in place under the front cradle sheer plate (2).
Front Wheelhouse Liner Bolt (1) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Crossmember Brace Bolt (3) - Install and tighten [8x] - Fastener Specifications
Front Cradle Shear Plate Nut (2) - Install and tighten [2x] - Fastener Specifications
Front Cradle Shear Plate Bolt (1) - Install and tighten [4x] - Fastener Specifications
Remove the jack.
Courtesy of GENERAL MOTORS COMPANY

Front Bumper Fascia Air Deflector Retainer (2) - Install
Front Bumper Fascia Air Deflector Bolt (1) - Install and tighten [4x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Front Compartment Air Deflector- Left Side and Right Side (1) - Install
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Front Bumper Fascia Lower Stiffener Bolt- Left Side and Right Side (3) - Install and tighten [6x] - Fastener Specifications
Front Compartment Air Deflector Retainer- Left Side and Right Side (2) - Install [2x]
Front Wheelhouse Liner Bolt- Left Side and Right Side (1) - Install and tighten [4x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Front Brake Rotor Cooling Duct Deflector (1) - Install
Front Brake Rotor Cooling Duct Deflector Bolt (2) - Install and tighten [3x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Install the 2 chassis harness retainers (1).
Install the front tire and wheel assembly. Tire and Wheel Removal and Installation
Lower the vehicle.
Measure and adjust the front toe. Wheel Alignment - Steering Wheel Angle and/or Front Toe Adjustment