LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2008 >> XLR Base >> Repair and Diagnosis >> Transmission >> Hydraulic Diagrams >> Automatic Transmission - 6L50/6L80/6L90 - Removal & Installation, Service, Overhaul, Troubleshooting & Diagnosis >> Repair Instructions - On Vehicle >> Transmission Fluid Cooler Upper Pipe Assembly Replacement >> Installation Procedure

Installation Procedure

  1. Install the TOC lines. Refer to Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection .
  2. Connect the oil level sensor electrical connector.
    3. Fig 1: TOC Inlet & Outlet Lines
    GM1218468Courtesy of GENERAL MOTORS CORP.
  3. Connect the front TOC lines to the rear TOC line set.
  4. Connect the upper and lower TOC retainer clip.
  5. Install the TOC line to oil pan retaining clips.
    6. NOTE: Refer to Fastener Notice .
  6. Install the TOC line to oil pan retaining nuts.

    Tighten:  Tighten the nuts to 12 N.m (9 lb ft).

  7. Lower the vehicle.
    8. IMPORTANT: When installing the engine mount, be sure to have the locating dowel in the correct position.
  8. Install the RH engine mount.
    9. Fig 2: View Of Engine Mount Heat Shield
    GM1334605Courtesy of GENERAL MOTORS CORP.
  9. Install the RH engine mount heat shield to the engine mount.
  10. Install the RH engine mount bracket.
    11. Fig 3: View Of Right Engine Mount Bracket & Bolts
    GM1334624Courtesy of GENERAL MOTORS CORP.
  11. Install the RH engine mount bracket bolts.

    Tighten:  Tighten the bolts to 58 N.m (43 lb ft).

  12. Using the J 28467-B  , lower the engine assembly into position.
  13. Install the RH engine mount lower nut

    Tighten:  Tighten the nut to 58 N.m (43 lb ft).

    14. Fig 4: View Of Right Engine Mount, Bracket & Nut
    GM1334619Courtesy of GENERAL MOTORS CORP.
  14. Install the RH engine mount upper nut.

    Tighten:  Tighten the nut to 58 N.m (43 lb ft).

  15. Install the A/C compressor and power steering pump bracket.
    16. Fig 5: Identifying Air Conditioning/Power Steering Bracket
    GM1252851Courtesy of GENERAL MOTORS CORP.
  16. Install the A/C compressor and power steering pump bracket bolts.

    Tighten:  Tighten the bolts to 50 N.m (37 lb ft).

    17. Fig 6: Identifying Accessory Belt Tensioner, Top & Lower Bolt
    GM927924Courtesy of GENERAL MOTORS CORP.
  17. Install the accessory belt tensioner.
  18. Install the accessory belt tensioner top bolt (1).
    IMPORTANT: Tighten in sequence.

    Tighten:  Tighten the bolt to 25 N.m (18 lb ft).

  19. Install the accessory belt tensioner lower bolt (2).

    Tighten:  Tighten the bolt to 25 N.m (18 lb ft).

  20. Install the A/C compressor. Refer to Compressor Replacement .
    21. Fig 7: View Of Auxiliary Transmission Oil Cooler
    GM1715293Courtesy of GENERAL MOTORS CORP.
  21. Install the lower TOC line to the auxiliary TOC. Refer to Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection .
  22. Connect the lower TOC line to the auxiliary TOC.
    23. Fig 8: View Of Lower Transmission Oil Cooler Line
    GM1715295Courtesy of GENERAL MOTORS CORP.
  23. Install the lower TOC line to the radiator. Refer to Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Disconnection and Connection .
  24. Connect the lower TOC line to the radiator.
  25. Install the wheelhouse panel. Refer to Wheelhouse Panel Replacement - Left Side .
  26. Lower the vehicle.
  27. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
  28. Check the transmission fluid level, add if necessary. Refer to Transmission Fluid Fill Procedure .
scientia non olet · About LEMON Manuals