LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2006 >> STS Base, 3.6 7, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine Mechanical - 4.4L (1 Of 5)) >> On-Vehicle Repair Instructions (Part 1) >> Camshaft Position Actuator Housing Replacement - Right Side >> Installation Procedure

Installation Procedure

WARNING: This page is about a different variant/trim than selected.
    Fig 1: View Of Camshaft Position Actuator Housing Gasket & Alignment Pins
    GM1040910Courtesy of GENERAL MOTORS CORP.
  1. Install a NEW gasket to the camshaft position actuator housing.
    2. Fig 2: View Of Right Camshaft Position Actuator Housing
    GM1276305Courtesy of GENERAL MOTORS CORP.
  2. Install the right camshaft position actuator housing to the right cylinder head.
    3. NOTE: Refer to Fastener Notice .
  3. Install the actuator housing bolts and studs.

    Tighten:  Tighten the actuator housing bolts and studs to 10 N.m (89 lb in).

    4. Fig 3: View Of Right Intake Camshaft Position Actuator Solenoid
    GM1276389Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: The camshaft position actuator solenoids must be precisely aligned to the camshaft position actuator oil control valves on the end of the camshafts. This is accomplished with an alignment pin. Failure to align the camshaft position actuator solenoids to the camshaft position actuator oil control valves can lead to poor engine performance and engine component damage.
  4. To allow for camshaft position actuator solenoid to camshaft position actuator oil control valve alignment, DO NOT install NEW camshaft position actuator solenoid alignment plugs at this time.
  5. Use the following procedure for the camshaft position actuator solenoid alignment:
    1. Make an alignment pin from drill rod 15/64 inch diameter and at least 50 mm (1.97 in) long.
    2. Verify that the alignment pin will pass through the camshaft position actuator solenoid alignment hole.
    3. Verify that the alignment pin will fit into the alignment hole in the camshaft position actuator oil control valve.
    4. Apply a 2 mm (0.079 in) bead of RTV around the flange of the camshaft position actuator solenoid. Refer to Sealers, Adhesives, and Lubricants for the correct part number.
    5. Install the camshaft position actuator solenoid over the oil control valve.
    6. Install the alignment pin through the solenoid alignment hole and into the oil control valve alignment hole.
    7. With the alignment pin in place, install the camshaft position actuator solenoid bolts.

      Tighten:  Tighten the camshaft position actuator solenoid bolts to 8 N.m (71 lb in).

    8. Remove the alignment pin.
    9. Install a NEW camshaft position actuator solenoid plug.
    10. Repeat steps 4-9 for the exhaust camshaft position actuator solenoid.
  6. Install the right camshaft cover. Refer to Camshaft Cover Replacement - Right Side .
    7. Fig 4: View Of Right Intake Camshaft Sensor & Right Exhaust Camshaft Sensor
    GM928266Courtesy of GENERAL MOTORS CORP.
  7. Install the right intake camshaft sensor. Refer to Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake .
  8. Install the right exhaust camshaft sensor. Refer to Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust .
  9. Install the camshaft sensor harness to the retainers.
  10. Install the supercharger drive belt tensioner. Refer to Drive Belt Tensioner Replacement - Supercharger .
  11. Install the water outlet housing. Refer to Water Outlet Housing Replacement (LC3) .
  12. Install the supercharger assembly. Refer to Supercharger Replacement .
  13. Install the supercharger inlet duct assembly. Refer to Supercharger Inlet Duct Assembly Replacement .
  14. Install the engine sight shield. Refer to Intake Manifold Sight Shield Replacement .
scientia non olet · About LEMON Manuals