LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2004 >> CTS Base, 3.2 N >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 6 (Automatic Transmission - 5L40-E (Introduction, Service & Replacement)) >> Repair Instructions >> Manual Shaft Shift Position Switch Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different variant/trim than selected.
    Fig 1: Installing Manual Shift Shaft Position Switch
    GM796173Courtesy of GENERAL MOTORS CORP.
  1. Install the manual shift shaft position switch (6), the manual shift shaft detent lever (4), the manual shift shaft assembly spacer (3), and the park pawl actuator (2) as an assembly. It may be necessary to push up on the park pawl in order to fully insert the park pawl actuator (2).
  2. Fully insert the manual shift shaft (1) into the transmission case.
  3. Raise the transmission to its original position.
  4. Install the transmission support. Refer to Transmission Support Replacement in Frame and Underbody.
  5. Remove the transmission jack.
    6. Fig 2: Installing Control Valve Body Bolts Retaining Manual Shift Shaft Detent Spring
    GM795840Courtesy of GENERAL MOTORS CORP.
  6. Install the manual shift shaft detent spring (1).
  7. Install the control valve body bolts (2) retaining the manual shift shaft detent spring. Do not tighten at this time.
    8. Fig 3: Confirming Manual Shift Shaft Detent Lever Locating Pin Is Properly Engaged
    GM795843Courtesy of GENERAL MOTORS CORP.
  8. Confirm that the manual shift shaft detent lever locating pin (2) is properly engaged with the manual valve link (1).
  9. Confirm that the detent spring roller (4) is properly engaged with the manual shift shaft switch (3).
    10. Fig 4: Installing Manual Shift Shaft Position Switch Retaining Pin
    GM795841Courtesy of GENERAL MOTORS CORP.
  10. Using a suitable pin punch (1). Install the manual shift shaft position switch retaining pin (2).
  11. Connect the electrical connector to the manual shift shaft position switch.
    12. Fig 5: Installing 0.8 mm Spacer
    GM822502Courtesy of GENERAL MOTORS CORP.
  12. Install a 0.8 mm spacer (2) between the manual shaft detent lever (1) and the manual shaft detent spring (3).
    13. NOTE: Refer to Fastener Notice in Cautions and Notices.
  13. Tighten the detent spring bolts.

    Tighten:  Tighten the bolts to 11 N.m (97 lb in).

  14. Remove the spacer (2).
  15. Install the transmission fluid pan and filter. Refer to Automatic Transmission Fluid/Filter Replacement .
    16. Fig 6: Install New Shaft Seal
    GM812780Courtesy of GENERAL MOTORS CORP.
  16. If previously removed, install a new shaft seal using J 44767  . See Special Tools and Equipment .
  17. Position the seal onto the J 44767  before installing the seal into the transmission case. See Special Tools and Equipment .
  18. Carefully slide the seal and tool over the manual shift shaft and Insert the seal into the transmission until fully seated
    19. Fig 7: Installing New Cup Plug
    GM812778Courtesy of GENERAL MOTORS CORP.
  19. If previously removed, install a new cup plug. Lubricate the cup plug with transmission fluid before installation.
  20. Insert the cup plug into the transmission until flush with the transmission case.
    21. Fig 8: Securing Front Propeller Shaft To Shift Control Lever With Mechanics Wire
    GM787650Courtesy of GENERAL MOTORS CORP.
  21. Remove the mechanics wire (2) securing front propeller shaft (1) to the shift control lever (3).
    22. Fig 9: View Of Propeller Shaft Coupler
    GM801931Courtesy of GENERAL MOTORS CORP.
  22. Install the propeller shaft coupler (1) to the transmission flange. Refer to Propeller Shaft Replacement (Automatic Transmission) , Propeller Shaft Replacement (Manual Transmission) or Propeller Shaft Replacement (CTS-V) in Driveline/Axle.
  23. Install the exhaust system. Refer to Exhaust System Replacement (LA3, LY9) , Exhaust System Replacement (LY7) or Exhaust System Replacement (LS6) in Engine Exhaust.
    24. Fig 10: Identifying Shift Linkage
    GM785877Courtesy of GENERAL MOTORS CORP.
  24. Connect the shift linkage to the transmission manual shift shaft.
  25. Install the transmission manual shift shaft nut.

    Tighten:  Tighten the nut to 15 N.m (11 lb ft).

  26. Adjust the shift control linkage. Refer to Shift Control Linkage Adjustment .
  27. Lower the vehicle.
scientia non olet · About LEMON Manuals