Test Description

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

2: During the heated seat relay operation, listen for an audible click from the relay. Repeat the commands, as necessary.
4: This step verifies that the BCM is providing voltage to the heated seat relay.
5: This step tests for an open in the ground circuit to the heated seat relay.

DTC B2508 or B2509:

Step	Action	Yes	No
Schematic Reference: Driver Seat Schematics or Passenger Seat Schematics Connector End View Reference: Power Seat Systems Connector End Views or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems
1	Did you perform the Diagnostic System Check - Vehicle?	Go to Step 2	Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2	Install a scan tool. Turn ON the ignition, with the engine OFF. With a scan tool, navigate to the appropriate Driver or Passenger Heated Seat output control screen by making the following selections: Body control module (BCM) Special functions Output control Miscellaneous tests Access the heated seat relay in order to verify operation. With a scan tool, command the appropriate Heated Seat ON and OFF. Does the heated seat relay turn ON and OFF with each command?	Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems	Go to Step 3
3	Turn OFF the ignition. Disconnect the heated seat relay. Turn ON the ignition, with the engine OFF. Connect a test lamp from the heated seat relay control circuit of the relay connector to ground. Does the test lamp illuminate?	Go to Step 9	Go to Step 4
4	Connect a test lamp between the heated seat relay control circuit of the relay connector to ground. With a scan tool, command the Heated Seat Relay ON and OFF. Does the test lamp turn ON and OFF with each command?	Go to Step 5	Go to Step 6
5	Connect a test lamp between the heated seat relay control circuit of the relay connector to the ground circuit of the relay of the relay connector. With a scan tool, command the Heated Seat Relay ON and OFF. Does the test lamp turn ON and OFF with each command?	Go to Step 7	Go to Step 10
6	Test the heated seat relay control circuit of the heated seat relay for a short to ground or an open. Refer to Circuit Testing andWiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 13	Go to Step 8
7	Inspect for poor connections at the harness connector of the heated seat relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 13	Go to Step 11
8	Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections andConnector Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 13	Go to Step 12
9	Repair the short to battery positive voltage in the heated seat relay control circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair?	Go to Step 13	-
10	Repair the open in the ground circuit of the heat seat relay. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair?	Go to Step 13	-
11	Replace the heated seat relay. Refer to Relay Replacement (Within an Electrical Center) or Relay Replacement (Attached to Wire Harness) in Wiring Systems. Did you complete the replacement?	Go to Step 13	-
12	Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming. Did you complete the replacement?	Go to Step 13	-
13	Use the scan tool in order to clear the DTCs. Operate the vehicle within the Conditions for Running the DTC. Does the DTC reset?	Go to Step 2	System OK