Cuts Out, Misses

WARNING: This page is about a different car, the 2006 Buick LaCrosse and 2006 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.

Cuts Out, Misses

Inspections	Action
DEFINITION: A steady pulsation or jerking that follows engine speed, which is usually more pronounced as the engine load increases. This condition is not normally felt above 1,500 RPM or 48 km/h (30 mph). The exhaust has a steady spitting sound at idle or at low speed.
Preliminary	Refer to Important Preliminary Inspections Before Starting in Symptoms - Engine Controls . Search for bulletins. Inspect the engine control system grounds for being clean, tight and in the correct locations. Refer to Power and Grounding Component Views in Wiring Systems and Engine Controls Schematics . Ensure the resistance between the engine control module (ECM) housing and the battery negative cable is less than 0.5 ohms. Verify that the ECM and ECM bracket fasteners are at the correct torque. Remove the air filter element and inspect for restrictions. Refer to Air Cleaner Element Replacement . Inspect the intake air duct and air cleaner outlet resonator for the following conditions: Restrictions Improperly installed hoses Leaks Collapsed hoses
Fuel System	Test for incorrect fuel pressure. Refer to Fuel System Diagnosis . Test for a restricted fuel filter. Refer to Fuel System Diagnosis . Inspect the fuel system. Refer to Fuel System Diagnosis . Test for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (w/o Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (w/Special Tool) . Test the fuel injectors. Refer to Fuel Injector Coil Test . Test the items that cause an engine to run rich. For a rich condition, refer to DTC P2178 or DTC P2188 . Test the items that can cause an engine to run lean. For a lean condition, refer to DTC P2177 or DTC P2187 .
Sensor/System	Monitor the knock sensor (KS) system for excessive spark retard activity with a scan tool. Refer to Knock Sensor (KS) System Description , DTC P0327 or P0332 and DTC P0328 or P0333 .
Ignition System	Inspect for the correct installation of the ignition coil seals. Incorrect installation may allow water to enter the spark plug area. Inspect for moisture and corrosion. Test for proper ignition voltage output with a J 26792 Spark Tester. See Special Tools . If you suspect an ignition system condition, refer to Electronic Ignition (EI) System Diagnosis . Remove the spark plugs and inspect for the following conditions: Incorrect heat range Wet plugs Cracks Wear Improper gap Burned electrodes Heavy deposits Refer to the following procedures: Spark Plug Replacement Ignition System Specifications Spark Plug Inspection If the spark plugs are gas, coolant or oil fouled, determine the cause before replacing the spark plugs. Refer to the following procedures: For diagnosis of a rich condition, refer to DTC P2178 or DTC P2188 . For diagnosis of coolant contaminated spark plugs, refer to Loss of Coolant in Engine Cooling. For diagnosis of oil fouled spark plugs, refer to Oil Consumption Diagnosis in Engine Mechanical - 3.6L (LY7). Inspect the spark plug boots and terminals for burning or micro-arcing, corrosion and damage to the insulation. Inspect the crankshaft position (CKP) sensor for the correct resistance. The sensor resistance may be out of range after a hot soak. Measure that the resistance remains within 700-1,200 ohms at all temperatures.
Engine Mechanical	Inspect for the following engine mechanical conditions: Excessive oil in combustion chamber or leaking valve seals Incorrect cylinder compression Sticking or leaking valves Worn camshaft lobes Camshaft timing Broken valve springs Excessive carbon buildup in the combustion chambers-Clean the chambers with top engine cleaner. Follow the instructions on the can. For more information, refer to the following procedures in Engine Mechanical - 3.6L (LY7): Oil Consumption Diagnosis Engine Compression Test Camshaft Timing Drive Chain Alignment Diagram (W/Primary Inverted Tooth (IT) Chain) Setting Camshaft Timing Symptoms - Engine Mechanical Inspect the following components for incorrect basic engine parts: Camshafts Cylinder heads Pistons, connecting rods or bearings. Refer to the following procedures in Engine Mechanical - 3.6L (LY7): Camshaft Timing Drive Components Cleaning and Inspection Camshaft Cleaning and Inspection Cylinder Head Cleaning and Inspection Piston, Connecting Rod and Bearings Cleaning and Inspection
Additional	Inspect the following exhaust system components: The exhaust system for damage The mufflers for heat distress or possible internal failure The three-way catalytic converters for restrictions For more information, refer to Symptoms - Engine Exhaust . Electromagnetic interference (EMI) on the CKP sensor signal circuits can cause an engine misfire condition. You can usually detect EMI with a scan tool by monitoring the engine speed parameter. A sudden increase in the engine speed parameter, with little change in actual engine speed indicates that EMI is present. Inspect for high voltage components near the ignition control circuits if a condition exists. Also, inspect the engine ground shield of the CKP sensor circuits.