LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2004 >> Century Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 100 (Lighting Systems) >> Diagnostic Information and Procedures >> DTC C0277 >> Diagnostic Aids

Diagnostic Aids

WARNING: This page is about a different car, the 2004 Pontiac Grand Prix. However, it is still accessible from the selected car via links, so may be relevant.

Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

DTC C0277

Step Action Yes No
Schematic Reference: Exterior Lights Schematics 
Connector End View Reference: Master Electrical Component List in Wiring Systems
1 Did you perform the Lighting System Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Lighting Systems 
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the brake current position sensor parameter in the data list for the BCM control module.
  4. Apply and release the brake pedal.
Does the scan tool display a change in the voltage?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3 Test for a open or poor connection in the stop lamp switch sensor signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 12  Go to Step 4 
4 Test for a short to battery positive voltage in the brake pedal position sensor low reference circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 12  Go to Step 5 
5 Test for a short to battery positive voltage short to ground or an open on the 10-volt reference circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 12  Go to Step 6 
6 Test for a short to ground in the I/P dimming voltage reference circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 12  Go to Step 7 
7 Inspect for a high resistance or a poor connection at the harness connector of the brake position sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 12  Go to Step 8 
8
IMPORTANT: Always recalibrate the brake pedal position sensor after replacing the brake position sensor. Refer to Brake Pedal Position Sensor Calibration Description and Operation .
Replace the brake pedal position sensor. Refer to Brake Pedal Position Sensor Replacement .Did you complete the repair?		 Go to Step 9  -
9
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Apply and release the brake pedal.
Does DTC C0277 reset?		 Go to Step 10  Go to Step 12 
10 Inspect for a high resistance or a poor connection at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 12  Go to Step 11 
11
IMPORTANT: After replacing the BCM, perform the setup procedure. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.
Replace the body control module. Refer to Body Control Module Replacement in Body Control System.Did you complete the replacement?		 Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals