Installing the component carrier

• Check centering sleeves (1)  in the marked  area for damage and replace centering sleeves (1)  if necessary.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Clean sealing surfaces (1) with special tool  0 495 102 (11 4 470)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide the connecting pipe (1)  out of the component carrier (2)  in the arrow direction and remove it.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace sealing rings (1)  on thee connecting pipe (2)  .
• Parts:  Sealing ring
• Coat sealing rings (1)  with coolant before installing.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide the connecting pipe (1)  in the arrow direction and install it on the component carrier (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace sealing ring (1)  .

  Parts:  Sealing ring

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert and install function carrier (1)  using the connecting pipe (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Hand-tighten the bolts (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Hand-tighten the bolts (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screws (1)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Coolant pump with function carrier on crankcase
  M8x35	tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screws (1)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Coolant pump with function carrier on crankcase
  M8x35	tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert the holder (2)  for the engine and the transmission oil lines and position it.
• Tighten down screws (1)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Engine holder - transmission oil line on the engine mount
  M6X16	tightening torque	12 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure clamps (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock coolant line (1)  .
• Make sure that the coolant line (1)  engages audibly.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE COOLANT LINE BETWEEN THE CYLINDER HEAD AND THE COOLANT PUMP .
• Refer to INSTALLING AIR CONDITIONING COMPRESSOR .
• Refer to EVACUATE AND CHARGE CONDITIONING .
• Refer to INSTALLING THE ALTERNATOR .
• Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR .
• Refer to INSTALLING THE THROTTLE BODY .
• Refer to INSTALLING CHARGE AIR LINE .
• Refer to INSTALLING CLEAN AIR PIPE .
• Refer to INSTALLING INTAKE FILTER HOUSING .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to IF INSTALLED: INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT (PARTIALLY REMOVED) .
• Refer to INSTALLING THE COVER FOR CENTER ENGINE COMPARTMENT .
• Refer to INSTALLING THE FRONT HOOD SEAL .
• Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
• Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
• Refer to IF INSTALLED: INSTALL UNDERBODY PROTECTION FOR THE STEERING .
• Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .