Installing air conditioning compressor
Preparing for the installation of the air-conditioning compressor
- Screw the screws (2) into the threaded support bushings (1).
- Push back the threaded support bushings (1) with the help of screws (2) slightly in the arrow direction.
- Unscrew the screws (2) out of the threaded support bushings (1).
NOTE:
TECHNICAL INFORMATION
Secure component against falling.
Secure component against falling.
- Replace O-rings.
Parts: O-rings
- Insert and position the air conditioning compressor (1) from above.
- Correctly position the refrigerant lines on the air conditioning compressor (1).
- Tighten down screws (2).
TIGHTENING TORQUE SPECIFICATIONS
| Refrigerant line on air conditioning compressor | ||
|---|---|---|
| M8 | tightening torque | 19 Nm |
- Correctly position the air conditioning compressor (2).
- Tighten down screws (1).
TIGHTENING TORQUE SPECIFICATIONS
| Air conditioning compressor in component carrier | ||
|---|---|---|
| M10 | Tightening torque | 38 Nm |
- Push coolant hose (1) slightly to the side.
- Connect connectors (2) and lock.
Follow-up work
- Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR .
- Refer to INSTALLING THE THROTTLE BODY .
- Refer to INSTALLING THE ENGINE CONTROL UNIT COVER .
- Refer to INSTALLING CHARGE AIR LINE .
- Refer to INSTALLING THE CLEAN AIR PIPE AND THE RESONATOR .
- Refer to INSTALLING THE INTAKE FILTER HOUSING (TENSION STRUT REMOVED ON SHOCK TOWER) .
- Refer to INSTALLING FAN COWL .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
- Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
- Refer to INSTALLING UPPER CROSS CONNECTION .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT , and INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE TOP RIGHT .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to EVACUATE AND CHARGE CONDITIONING .
- Refer to RUNNING IN THE NEW AIR CONDITIONING COMPRESSOR .
Preparing for the installation of the air-conditioning compressor
- Screw the screws (2) into the threaded support bushings (1).
- Push back the threaded support bushings (1) with the help of screws (2) slightly in the arrow direction.
- Unscrew the screws (2) out of the threaded support bushings (1).
NOTE:
TECHNICAL INFORMATION
Secure component against falling.
Secure component against falling.
- Replace O-rings.
Parts: O-rings
- Insert and position the air conditioning compressor (1) from above.
- Correctly position the refrigerant lines on the air conditioning compressor (1).
- Tighten down screws (2).
TIGHTENING TORQUE SPECIFICATIONS
| Refrigerant line on air conditioning compressor | ||
|---|---|---|
| M8 | tightening torque | 19 Nm |
- Correctly position the air conditioning compressor (2).
- Tighten down screws (1).
TIGHTENING TORQUE SPECIFICATIONS
| Air conditioning compressor in component carrier | ||
|---|---|---|
| M10 | Tightening torque | 38 Nm |
- Push coolant hose (1) slightly to the side.
- Connect connectors (2) and lock.
Follow-up work
- Refer to INSTALLING THE DRIVE BELT FOR THE STARTER MOTOR GENERATOR .
- Refer to INSTALLING CHARGE AIR LINE .
- Refer to INSTALLING THE CLEAN AIR PIPE AND THE RESONATOR .
- Refer to INSTALLING THE INTAKE FILTER HOUSING (TENSION STRUT REMOVED ON SHOCK TOWER) .
- Refer to INSTALLING FAN COWL .
- Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
- Refer to INSTALLING UPPER CROSS CONNECTION .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT , and INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE TOP RIGHT .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE BRACKET FOR THE DME CONTROL UNIT .
- Refer to INSTALLING THE ENGINE CONTROL UNIT COVER .
- Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
- Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to EVACUATE AND CHARGE CONDITIONING .
- Refer to RUNNING IN THE NEW AIR CONDITIONING COMPRESSOR .