Remove bearing bracket
CAUTION:
High-voltage system.
The high-voltage system operates on the basis of hazardous, electrical voltage and high currents. Mortal hazard through electric shock!
The high-voltage system operates on the basis of hazardous, electrical voltage and high currents. Mortal hazard through electric shock!
- All work on the high-voltage system may only be carried out by specially trained and technically experienced personnel.
- For additional information see: 61 00... SAFETY INSTRUCTIONS on handling hybrid cars
- For additional information see: 61 25... NOTES on repair of high-voltage battery unit
WARNING:
Heavy component falling down or tipping.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Before lowering or removing the front axle: Secure the engine in the installation position.
- For additional information see: 11 00 670 Securing engine in INSTALLATION POSITION .
WARNING:
Car may slip off the vehicle hoist where components are supported.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Secure the vehicle hoist against lowering and lifting.
WARNING:
Vehicle may slip off the vehicle hoist if the vehicle hoist is handled incorrectly.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Observe safety instructions on raising the vehicle using a vehicle hoist.
- For additional information see: 00... Raise the vehicle using a VEHICLE LIFT. .
WARNING:
Car may slip off the vehicle hoist if the weight is distributed unevenly.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Ensure there is a specific weight compensation on the car.
Preliminary work
- Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
- Refer to REMOVING FLAP IN LUGGAGE COMPARTMENT TRIM PANEL ON RIGHT .
- Refer to DE-ENERGIZING THE HIGH-VOLTAGE SYSTEM .
- Refer to CHECKING THAT NO VOLTAGE IS APPLIED .
- Refer to DISCONNECTING THE NEGATIVE BATTERY CABLE (STARTER UNIT BATTERY) .
- Refer to REMOVING BATTERY COVER IN TRUNK .
- Refer to DISCONNECTING THE NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
- Refer to REMOVING THE COVER OF THE ENGINE COMPARTMENT AT THE REAR LEFT .
- Refer to REMOVING THE COVER OF THE REAR RIGHT ENGINE COMPARTMENT .
- Refer to REMOVING THE SEAL FOR THE HOOD REAR .
- Refer to REMOVING LEFT AND RIGHT WIPER ARM
- Refer to REMOVING THE COWL COVER .
- Refer to REMOVING THE ACOUSTIC COVER .
- Refer to REMOVING THE BULKHEAD UPPER PART .
- Refer to REMOVING ACOUSTIC COVER AT REAR .
- Refer to REMOVING ALL IGNITION COILS .
- Refer to REMOVING FUEL DELIVERY LINE
- Refer to REMOVING THE TOP RIGHT AND LEFT COVER IN THE ENGINE COMPARTMENT .
- Refer to REMOVING STAND FOR THE HOOD GASKET LEFT AND RIGHT .
- Refer to REMOVING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
- Refer to REMOVING THE CENTER UNDERBODY PROTECTION .
- Refer to REMOVING REAR UNDERBODY PROTECTION .
- Refer to REMOVING THE COVER PANEL FOR THE FRONT AXLE LEFT AND RIGHT .
- Refer to INSTALLING THE ENGINE BRIDGE
- Refer to RELEASING THE ENGINE SUPPORT BRACKETS ON THE ENGINE MOUNTS ON LEFT AND RIGHT .
- Refer to RAISING THE ENGINE WITH THE ENGINE BRIDGE
- Refer to DETACHING STEERING SHAFT AT BOTTOM FROM STEERING GEAR .
- Refer to RELEASING THE EPS WIRING HARNESS FROM THE ELECTROMECHANICAL STEERING GEAR .
- Refer to DETACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR .
- Refer to IF INSTALLED: DISCONNECT THE VACUUM LINE OF THE ENGINE MOUNTS .
- Refer to DETACHING THE ANTI-ROLL BAR LINK FROM THE ANTI-ROLL BAR ON THE RIGHT AND LEFT .
- Refer to RELEASING THE TIE ROD ON THE RIGHT FROM THE SWIVEL BEARING .
- Refer to RELEASING THE OUTPUT SHAFT, RIGHT, FROM THE WHEEL BEARING .
- Refer to RELEASING THE WISHBONE ON THE RIGHT FROM THE SWIVEL BEARING .
- Refer to REMOVE RIGHT OUTPUT SHAFT .
- Refer to PREPARING THE SPECIAL TOOL .
- Refer to SUPPORT THE FRONT AXLE SUPPORT .
- Refer to SECURING THE FRONT AXLE SUPPORT AT THE SPECIAL TOOL .
- Refer to DETACHING AND LOWERING THE FRONT AXLE SUPPORT
- Refer to DETACHING THE ACOUSTIC COVER FROM THE OIL SUMP .
- Loosen screws (1).
- Remove bearing bracket (2).