Remove the acoustic cover of the oil sump
WARNING:
Heavy component falling down or tipping.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Before lowering or removing the front axle: Secure the engine in the installation position.
- For additional information see: 11 00 670 Securing engine in INSTALLATION POSITION .
WARNING:
Car may slip off the vehicle hoist where components are supported.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Secure the vehicle hoist against lowering and lifting.
WARNING:
Vehicle may slip off the vehicle hoist if the vehicle hoist is handled incorrectly.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Observe safety instructions on raising the vehicle using a vehicle hoist.
- For additional information see: 00... Raise the vehicle using a VEHICLE LIFT. .
WARNING:
Car may slip off the vehicle hoist if the weight is distributed unevenly.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- Ensure there is a specific weight compensation on the car.
Preliminary work
- Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
- Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
- Refer to REMOVING THE COVER OF THE ENGINE COMPARTMENT AT THE REAR LEFT .
- Refer to REMOVING THE COVER OF THE REAR RIGHT ENGINE COMPARTMENT .
- Refer to REMOVING THE SEAL FOR THE HOOD REAR .
- Refer to REMOVING THE TOP RIGHT AND LEFT COVER IN THE ENGINE COMPARTMENT .
- Refer to REMOVING STAND FOR THE HOOD GASKET LEFT AND RIGHT .
- Refer to REMOVING THE ACOUSTIC COVER .
- Refer to REMOVING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to REMOVING THE COVER PANEL FOR THE FRONT AXLE LEFT AND RIGHT .
- Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
- Refer to REMOVING THE CENTER UNDERBODY PROTECTION .
- Refer to REMOVING COVER ON THE EXHAUST SYSTEM .
- Refer to REMOVING REAR UNDERBODY PROTECTION .
- Refer to DETACHING STEERING SHAFT AT BOTTOM FROM STEERING GEAR .
- Refer to RELEASING THE EPS WIRING HARNESS FROM THE ELECTROMECHANICAL STEERING GEAR .
- Refer to DETACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR .
- Refer to IF INSTALLED: DISCONNECT THE VACUUM LINE OF THE ENGINE MOUNTS .
- Refer to RELEASING THE ELECTRIC COOLANT PUMP AND COOLANT HOSES FROM THE FRONT AXLE SUPPORT .
- Refer to DETACHING THE ANTI-ROLL BAR LINK FROM THE ANTI-ROLL BAR ON THE RIGHT AND LEFT .
- Refer to MOVE THE ENGINE TO THE INSTALLATION POSITION .
- Refer to PREPARING THE SPECIAL TOOL .
- Refer to SUPPORT THE FRONT AXLE SUPPORT .
- Refer to DETACHING AND LOWERING THE FRONT AXLE SUPPORT .
Prerequisite
Disconnect all negative battery cables GROUND LEADS .
- Unlock and release the plug connection (1).
- Loosen nut (2).
- Guide the positive battery cable (3) out of the clamp (4) and lay to one side.
- Unlock and loosen the clamps (1).
- Guide out the wiring harness section for the automatic transmission (2) and set it aside.NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
- Loosen screw (1).NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
- Loosen the holder (1).NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
- Feed out the transmission oil lines (1) from the holder (2) and place to one side.
- Loosen the expanding rivet (1).
- Loosen the expanding rivet (1).
- Loosen the expanding rivet (1).
- Undo Christmas tree clip (2).
- Guide out and remove acoustic cover (1) of the oil pan.