Install engine

• Position the lifting table (1) with the engine under the vehicle.

  The marks made during removal (arrows) on the workshop floor are used as positioning aid.

  Courtesy of BMW OF NORTH AMERICA, INC.

  WARNING: Vehicle may slip off the vehicle hoist if the vehicle hoist is handled incorrectly  .
  Danger! Immobilization period-threatening injuries! 

  • Observe safety instructions on raising the vehicle using a vehicle hoist.
  • For additional information see: RAISING THE VEHICLE WITH A VEHICLE LIFT) .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Lower the vehicle carefully  and if necessary, correct  the positioning of the lifting table.
• Replace screws (1).

  Parts:  Screws

• Tighten down screws (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Transmission mounting
  M10 Replace screws.	Joining torque	40 Nm
  	Angle of rotation	90°

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace screws (1).

  Parts:  Screws

• Tighten down screws (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Right engine mount to cylinder head
  M10 Replace screws.	Joining torque	40 Nm
  	Angle of rotation	90°

  Courtesy of BMW OF NORTH AMERICA, INC.

  WARNING: Car may slip off the vehicle hoist if the weight is distributed unevenly  .
  Danger! Immobilization period-threatening injuries! 

  • Ensure there is a specific weight compensation on the car.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Take weight compensation (1) off of vehicle.
• Lower the lifting table (2) and set aside.
• Insert and install the ground strap (2).
• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Ground strap to transmission
  M8	tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect the vacuum line (2) and lock.
• Ensure that locks (1) engage audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install coolant line (2).
• Fasten the clamping collar (1) with the special tool 0 495 794 (17 2 050)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in the wiring harness section (3) and position.
• Secure clamps (2).
• Connect connectors (1) and lock.
• Make sure the connector (1) engages audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Slide out and remove the battery tray (4).
• Insert and install the coolant line (2) on the battery tray (4).
• Secure clamps (1).
• Tighten down screws (3).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Battery tray
  M8	tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert and install the battery positive terminal (2) and auxiliary terminal for jump starting (3).
• Tighten nuts (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Positive battery cable to positive battery terminal
  M8	Tightening torque	15 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install coolant line (1).
• Make sure that the coolant line (1) engages audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the coolant lines (1) and (2) on the heat management module (3).
• Make sure that the coolant lines (1) and (2) engage audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock coolant line (2).
• Make sure that the coolant line (2) engages audibly.
• Connect connectors (1) and lock.
• Make sure the connector (1) engages audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide out and remove special tools 0 496 565 (13 5 160) and 0 496 568 (13 5 162)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert and install the tank vent line (4).
• Make sure that the lock (3) snaps-in audibly.
• Guide the fuel delivery line (2) in and install.
• Make sure that the lock (1) snaps-in audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock coolant line (1).
• Make sure that the coolant line (1) engages audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Use standard tools to guide out and remove the coolant lines (2) and air conditioning compressor.
• Replace sealing ring (1).

  Parts:  Sealing ring

• Insert and install the sealing ring (1) on the refrigerant line (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert and install the coolant lines (3).
• Tighten down screws (2).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Refrigerant lines to air-conditioning compressor
  M8 Replace sealing rings.	Tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1) and lock.
• Make sure the connector (1) engages audibly.
• Feed in the coolant hoses on the transmission oil cooler and install.
• Ensure that locks (1) engage audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Open the weld seam (1) with a conventional tool.
• Remove ribbon clamp (2).
• Replace the (2) ribbon clamp.

  Parts:  Ribbon cable clamp

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten the ribbon clamp (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to PARTIALLY INSTALLING RIGHT OUTPUT SHAFT .
• Refer to PARTIALLY INSTALLING THE LEFT OUTPUT SHAFT .
• Refer to INSTALLING THE PRESSURE PIPE BETWEEN THE THROTTLE BODY AND THE CHARGE AIR COOLER .
• Refer to INSTALLING THE RIGHT CHARGE AIR DUCT BETWEEN THE EXHAUST TURBOCHARGER AND THE CHARGE AIR COOLER .
• Refer to MOUNTING AND SECURING THE COMPLETE FRONT AXLE .
• Refer to SECURING THE MOUNTED PART ON THE FRONT AXLE SUPPORT .
• Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
• Refer to ATTACHING CONNECTOR AT STEERING GEAR .
• Refer to FASTENING THE RUBBER MOUNT ON THE FRONT AXLE SUPPORT .
• Refer to SECURING THE ANTI-ROLL BAR ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR LINK .
• Refer to WITH RIGHT INSTALLATION: FASTENING THE CABLE FOR THE RIDE HEIGHT SENSOR .
• Refer to CONNECTING PURGE AIR LINE .
• Refer to INSTALLING STARTER MOTOR .
• Refer to INSTALLING THE WASHER FLUID RESERVOIR IN THE MOUNT .
• Refer to INSTALLING EXHAUST SYSTEM .
• Refer to INSTALLING THE CONNECTING SUPPORT ON THE TUNNEL AT FRONT AND REAR .
• Refer to INSTALLING THE CROSS-MEMBER WITH TORSION STRUTS .
• Refer to INSTALLING THE FRONT RIGHT WHEEL ARCH COVER .
• Refer to PARTIALLY INSTALLING THE FRONT WHEEL ARCH COVER .
• Refer to ATTACHING THE FRONT LEFT WHEEL .
• Refer to INSTALLING THE FRONT RIGHT WHEEL .
• Refer to REMOVING COOLANT RADIATOR ATTACHMENT ON THE LEFT AND RIGHT .
• Refer to REMOVING FRONT CROSS CONNECTION .
• Refer to REMOVING THE LOCATING PINS .
• Refer to INSTALLING FAN COWL WITH ELECTRIC FAN .
• Refer to INSTALLING FRONT CROSS CONNECTION .
• Refer to TOPPING UP THE MOTOR OIL .
• Refer to INSTALLING THE OIL FILLER CAP .
• Refer to FILLING THE COOLANT CIRCUIT WITH THE VACUUM FILLING EQUIPMENT .
• Refer to EVACUATE AND CHARGE CONDITIONING .
• Refer to INSTALLING E-BOX .
• Refer to INSTALLING THE SYSTEM BATTERY .
• Refer to INSTALLING THE UPPER FIREWALL COVER PANEL .
• Refer to CONNECTING THE BATTERY EARTH LEAD .
• Refer to INSTALLING INTAKE SILENCER HOUSING .
• Refer to INSTALLING THE INTAKE MANIFOLD FOR THE INTAKE FILTER HOUSING .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING THE STRUT BRACE .
• Refer to AIR BLEEDING THE COOLANT CIRCUIT .
• Refer to CHECKING ENGINE OIL LEVEL .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .