Installing the intake camshaft for cylinders 7 through 12

Left-hand intake camshaft

Fig 1: Intake Camshaft Screws Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

1-14 Screws (graphic N74)

Check the plain rectangular compression rings (1) on the intake camshaft for damage and, if necessary, replace them.
The snap-in lugs (arrows) of the plain rectangular compression rings must be locked in place.

Courtesy of BMW OF NORTH AMERICA, INC.
Make sure the rocker arms (1) are fitted correctly.
Coat all the bearing positions of the intake camshaft on the cylinder head with engine oil.

Courtesy of BMW OF NORTH AMERICA, INC.
Coat all bearing positions with motor oil.
Observe the camshaft identification.
All camshafts are identified and must never be mixed up.

I = Intake side, 712 = Cylinders 7 to 12

Courtesy of BMW OF NORTH AMERICA, INC.
Coat all bearing positions with motor oil.
Insert the intake camshaft without tension so that the identification is legible.
Observe the correct installation orientation of the roller cam follower (arrows).
The cams on cylinder 7 point upwards and outwards.

Courtesy of BMW OF NORTH AMERICA, INC.
Ensure that thrust bearing (1) of the intake camshaft is positioned correctly in the cylinder head.
The intake camshaft bearing cap of the thrust bearing (1) can be mounted in one position only.

Courtesy of BMW OF NORTH AMERICA, INC.
Position the lid (1) of the thrust bearing on the thrust bearing and hand-tighten (apply) the screws.
Position the high pressure pump bracket (2) and hand-tighten the screws.

Courtesy of BMW OF NORTH AMERICA, INC.
Coat all bearing positions with motor oil.
Observe the identification of the camshaft bearing caps.
All camshaft bearing cups are marked and must never be mixed up.

L = Cylinders 7 to 12, A = Exhaust side, 4 = Bearing position 4

R = Cylinder 1 to 6, E = Intake side

Courtesy of BMW OF NORTH AMERICA, INC.
Position all intake camshaft bearing caps (1) at their original installation locations and apply the screws hand-tight.

Courtesy of BMW OF NORTH AMERICA, INC.
Insert special tool 0 496 381 (11 9 893) .
Ensure that the special tool 0 496 381 (11 9 893) rests on the cylinder head without any gap after the exhaust camshaft is positioned.
If necessary, slightly rotate the intake camshaft.

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten (apply) the bolts to the snug torque in the sequence (14) to (1) in increments of 180°.

TIGHTENING TORQUE SPECIFICATIONS

Camshaft bearing cap to cylinder head
M7x45	Joining torque	15 Nm
M7x45	Tightening torque	15 Nm

Fig 2: Intake Camshaft Screws Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Ensure that all the intake camshaft bearing caps rest on the cylinder head without any gaps.

Tighten the screws in the sequence (14) to (1) with the tightening torque.

TIGHTENING TORQUE SPECIFICATIONS

Camshaft bearing cap to cylinder head
M7x45	Joining torque	15 Nm
M7x45	Tightening torque	15 Nm

Note the installation position (arrows) of the roller tappet during installation.
Installing roller tappet of high pressure pump.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to SCREW IN SPECIAL TOOLS 11 9 895 1 TO 6 AND 7 TO 12 .
Refer to FASTENING THE CAMSHAFTS WITH THE SPECIAL TOOL .
Refer to INSTALLING INTAKE ADJUSTER OF CYLINDERS 7 TO 12 .
Refer to REPLACING THE CENTRAL BOLT .
Refer to SECURING BOTH CENTRAL BOLTS OF THE VANOS GEAR .
Refer to INSTALLING THE UPPER SLIDE RAIL .
Refer to INSTALLING SPECIAL TOOL TO PRE-TENSIONING TIMING CHAIN .
Refer to SECURING THE CENTRAL BOLT OF THE VARIABLE CAMSHAFT TIMING CONTROL OF THE INTAKE .
Refer to SECURING THE CENTRAL BOLT OF THE VARIABLE CAMSHAFT TIMING CONTROL OF THE EXHAUST .
Refer to REMOVING THE SPECIAL TOOLS TO FIX THE CAMSHAFTS .
Refer to CHECKING TIMING .
Refer to REMOVING THE SPECIAL TOOLS TO DISCONNECTING THE CRANKSHAFT .
Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN .
Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER .
Refer to INSTALLING THE TOP TIMING CASE COVER OF CYLINDERS 7 TO 12 .
Refer to INSTALLING BOTH SOLENOID VALVES ON THE LEFT .
Refer to INSTALLING ALTERNATOR 2 .
Refer to INSTALLING THE HEATER RETURNING HOSE ON THE COOLANT PUMP .
Refer to INSTALLING THE LEFT COOLANT HOSE ON THE RADIATOR .
Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR .
Refer to MOUNTING AIR CONDITIONING COMPRESSOR .
Refer to INSTALLING THE BELT PULLEY .
Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR .
Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR 2 AND THE AIR CONDITIONING COMPRESSOR .
Refer to REMOVING THE PROTECTIVE PLATE AT THE RADIATOR .
Refer to INSTALLING THE ACTIVE STABILIZER IN FRONT .
Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE RIGHT .
Refer to INSTALLING THE FRONT RIGHT WHEEL .
Refer to INSTALLING THE STIFFENING PLATE .
Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
Refer to INSTALLING THE LEFT CYLINDER HEAD COVER .
Refer to ATTACHING COOLANT LINE FOR LEFT EXHAUST TURBOCHARGER .
Refer to PREPARING THE INJECTOR FOR INSTALLATION .
Refer to INSTALLING INJECTORS .
Refer to INSTALLING THE LEFT HIGH PRESSURE PUMP .
Refer to INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
Refer to INSTALLING ALL HIGH PRESSURE LINES BETWEEN THE RAIL AND THE INJECTORS .
Refer to INSTALLING FUEL DELIVERY LINE .
Refer to INSTALLING THE LEFT-HAND HIGH PRESSURE LINE BETWEEN THE HIGH PRESSURE PUMP AND THE RAIL .
Refer to INSTALLING CHARGE AIR PIPE ON LEFT .
Refer to INSTALLING TOP CLEAN AIR PIPE ON LEFT .
Refer to PARTIALLY FASTENING THE WIRING HARNESS ON THE LEFT CYLINDER HEAD COVER .
Refer to CONNECTING ALL THE CONNECTORS TO THE DME CONTROL UNIT FOR CYLINDERS 7 TO 12 .
Refer to INSTALLING COVER FOR THE LEFT DME CONTROL UNIT .
Refer to INSTALLING THE IGNITION COILS .
Refer to INSTALLING THE LEFT-HAND VENTILATION LINE .
Refer to INSTALLING THE INTAKE PLENUM .
Refer to INSTALLING THE TANK VENT LINE .
Refer to INSTALLING THE ENGINE VENTILATION LINE ON THE INTAKE SYSTEM .
Refer to INSTALLING FAN COWL .
Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
Refer to MOUNTING THE LEFT-HAND CHARGE AIR COOLER .
Refer to INSTALLING THE LEFT THROTTLE BODY .
Refer to INSTALLING LEFT INTAKE PORT .
Refer to INSTALLING THE LEFT-HAND AIR DUCT .
Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
Refer to MOUNTING THE RIGHT-HAND CHARGE AIR COOLER .
Refer to INSTALLING THE RIGHT THROTTLE BODY .
Refer to INSTALLING RIGHT AIR DUCT .
Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
Refer to INSTALLING THE CENTER COWL UPPER PART .
Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
Refer to INSTALLING WINDSHIELD PANEL COVER .
Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
Refer to INSTALLING FANFARE HORN, RIGHT .
Refer to INSTALLING THE FANFARE ON THE LEFT SIDE .
Refer to INSTALLING THE CENTER TOP CROSS CONNECTION .
Refer to INSTALLING BOTH HEADLIGHTS .
Refer to INSTALLING BUMPER COVER, FRONT .
Refer to INSTALLING FRONT SECTION OF THE FRONT WHEEL ARCH COVER (PARTIALLY REMOVED) .
Refer to INSTALLING FRONT ORNAMENTAL GRILLE .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
Refer to INSTALLING ACOUSTIC COVER .
Refer to CONNECTING ALL BATTERY GROUND LEADS .
Refer to FILLING THE COOLING SYSTEM WITH THE VACUUM FILLING UNIT .
Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
Refer to ADJUSTING HEADLIGHTS .