Checking the side clearance of the new piston rings
Precondition
Piston cleaned.
- Note the arrangement of the piston rings:
Upper piston ring (1) : Plain rectangular compression ring (engraving must point upwards)
Center piston ring (2) : Taper faced piston ring (engraving must point upwards)
Oil scraper ring (3) : consisting of 2 piston rings (O1) and (O3) with spring (O2) in the center
Check
- Use a feeler gauge to check the side clearance of the new upper piston ring (plain rectangular compression ring).
- Determining the correct set of the piston ring (1)
(see applicable BMW parts catalogue):
Engine Set of piston rings Pistons Side clearance of the upper piston ring B38M1 ECE 8 693 017 8 678 931 0.02 - 0.07 mm B38M1 ECE 8 693 017 9 494 399 0.04 - 0.08 mm B48M1 ECE 8 693 017 8 678 931 0.02 - 0.07 mm B48M1 ECE 8 693 017 9 494 399 0.04 - 0.08 mm B38M1 CN 8 693 017 8 678 931 0.02 - 0.07 mm B38M1 CN 9 847 276 8 681 079 0.035 - 0.085 mm B48M1 CN 8 693 017 8 678 931 0.02 - 0.07 mm B48M1 CN 9 847 276 8 681 079 0.035 - 0.085 mm B48O1 ECE+CN 8 693 017 8 678 934 0.02 - 0.07 mm B48T1 ECE+CN 9 846 014 9 488 343 0.03 - 0.07 mm B58M1 9 847 276 8 681 079 0.035 - 0.85 mm B58O1 9 693 017 8 678 934 0.02 - 0.07 mm
Result
» The side clearance is outside the tolerance.
Measure
- Replace the piston.
- Note the arrangement of the piston rings:
Upper piston ring (1) : Plain rectangular compression ring (engraving must point upwards)
Center piston ring (2) : Taper faced piston ring (engraving must point upwards)
Oil scraper ring (3) : consisting of 2 piston rings (O1) and (O3) with spring (O2) in the center.
Check
- Use a feeler gauge to check the side clearance of the new middle piston ring (taper faced piston ring).
- Determining the correct set of the piston ring (1)
(see applicable BMW parts catalogue):
Engine Set of piston rings Pistons Side clearance of the piston ring in the center B38M1 ECE 8 693 017 8 678 931 0.03 - 0.07 mm B38M1 ECE 8 693 017 9 494 399 0.03 - 0.07 mm B48M1 ECE 8 693 017 8 678 931 0.03 - 0.07 mm B48M1 ECE 8 693 017 9 494 399 0.03 - 0.07 mm B38M1 CN 8 693 017 8 678 931 0.03 - 0.07 mm B38M1 CN 9 847 276 8 681 079 0.015 - 0.06 mm B48M1 CN 8 693 017 8 678 931 0.03 - 0.07 mm B48M1 CN 9 847 276 8 681 079 0.015 - 0.06 mm B48O1 ECE+CN 8 693 017 8 678 934 0.03 - 0.07 mm B48T1 ECE+CN 9 846 014 9 488 343 0.025 - 0.07 mm B58M1 9 847 276 8 681 079 0.015 - 0.06 mm B58O1 9 693 017 8 678 934 0.03 - 0.07 mm
Result
» The side clearance is outside the tolerance.
Measure
- Replace the piston.