Removing the intake plenum

Preliminary work 

• Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
• Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
• Refer to REMOVING THE ACOUSTIC COVER .
• Refer to REMOVING THE SEAL FOR THE HOOD REAR .
• Refer to REMOVING ACOUSTIC COVER AT REAR .
• Refer to REMOVING THE CENTER ENGINE COMPARTMENT COVER .
• Refer to REMOVING BOTH FRONT-END STRUTS .
• Refer to REMOVING UPPER CROSS CONNECTION .
• Refer to REMOVING THE REAR TOP CROSS CONNECTION .
• Refer to REMOVING THE FAN COWL .
• Refer to REMOVING THE DME CONTROL UNIT .
• Refer to REMOVING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
• Refer to REMOVING CONTROL UNIT BRACKET .
• Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
• Refer to REMOVING THE UNDERBODY PROTECTION OF THE STEERING GEAR AND THRUST FIELD RESPECTIVELY .
• Refer to REMOVING THE FRONT BOTTOM RIGHT AND LEFT COVERS .
• Refer to DRAINING THE COOLANT FROM THE LOW-TEMPERATURE COOLING SYSTEM .
• Refer to CONNECTING THE COOLANT LINES FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to REMOVING TANK VENT VALVE .

• Loosen screw (1).
• Guide tank ventilation line (2) out of clamp (3) and remove it.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Unlock and release the plug connections (1).
• Unlock the locks (2).
• Guide tank ventilation line (3) out of clamp (4) and remove it.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Unlock the locks (1).
• Feed the tank ventilation line (2) out and set it aside.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Unlock the locks (1).
• Feed out the wiring harness section (2) for the sensor system 2 and set it aside.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen screws (1).
• Feed out charge air line (2) and place to one side.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Unlock and release plug connection (1),
• Loosen clamp (2).
• Thread off coolant line (3) and place to the side.
• Loosen screw (4),

  Courtesy of BMW OF NORTH AMERICA, INC.

• Unlock and release plug connection (1),

  Courtesy of BMW OF NORTH AMERICA, INC.

• Unlock the locks (arrows),
• Feed out the wiring harness section (1) for the injectors and ignition coils and put to one side.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide tank ventilation line (1) out of clamp (2) and place it aside.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed out the wiring harness section (1) for the injectors and ignition coils of the cylinder head cover (2) and put to one side.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen screw (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Unlock and loosen coolant line (1).
• Catch and dispose of escaping coolant.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen screws in the order (7) to (1).
• Slightly lift intake plenum (A) in arrow direction.
  Fig 1: Intake Plenum Screws Loosening Sequence

  Courtesy of BMW OF NORTH AMERICA, INC.
  NOTE: TECHNICAL INFORMATION 
  The tension rod screws and mounting bolts from the connecting neck on the intake plenum are not  allowed to be opened.
• Do not  release screws in the marked area  on the intake plenum (1). 

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  Additional coolant can leakage. Make sure that no coolant enters the intake port of the cylinder head.
• Unlock and release the coolant line (1)  under the intake plenum (2).
• Catch and dispose of escaping coolant.
• Feed out the intake plenum (2) and remove it.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Empty the remaining coolant (2) from the intake plenum (1). 

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  The tension rod screws and mounting bolts from the connecting neck on the intake plenum are not  allowed to be opened.
• Do not  release screws in the marked area  on the intake plenum (1). 

  Courtesy of BMW OF NORTH AMERICA, INC.