Install the oil vacuum pump
- Check guide sleeves (1)
for damage and replace if necessary.
Parts: Guide sleeves
- Make sure the sealing ring (1)
is installed correctly.
The sealing ring (1) must not be damaged or missing.
- Guide the oil vacuum pump (1)
into the drive chain (2)
.
- Position oil vacuum pump (2) correctly on the guide sleeves.
- Tighten the screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Oil vacuum pump to crankcase | ||
|---|---|---|
| M8 Replace screw. |
1. Joining torque | 15 Nm |
| 2. Angle of rotation | 45° | |
Follow-up work
- Refer to REFITTING SUMP .
- Refer to INSTALLING THE STARTER MOTOR (ACOUSTIC COVER REMOVED) .
- Refer to TIGHTENING THE OIL DRAIN PLUG .
- Refer to INSTALLING FRONT AXLE DIFFERENTIAL .
- Refer to INSTALLING BEARING BRACKET .
- Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL SUMP .
- Refer to IF INSTALLED ON LEFT: POSITION SPRAY GUARD .
- Refer to RAISING FRONT AXLE SUPPORT .
- Refer to TIGHTENING THE BOLTS ON THE FRONT AXLE SUPPORT .
- Refer to FASTENING THE SPRING STRUT HOLDER ON THE LEFT AND RIGHT TO THE WISHBONE BELOW .
- Refer to SECURING THE TOP WISHBONE ON THE SWIVEL BEARING .
- Refer to REMOVING THE MOBILE LIFTING TABLE .
- Refer to ATTACHING COOLANT HOSES TO FRONT SUBFRAME .
- Refer to SECURING THE RIGHT AND LEFT OUTPUT SHAFTS ON THE WHEEL BEARING .
- Refer to SECURING BRAKE HOSE, FRONT RIGHT AND LEFT .
- Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
- Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE STATIONARY HEATING .
- Refer to IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
- Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
- Refer to IF INSTALLED ON LEFT: INSTALLING SPRAY GUARD .
- Refer to IF INSTALLED: CONNECTING THE VACUUM HOSE OF THE ENGINE MOUNTING ON THE FRONT AXLE SUPPORT .
- Refer to TIGHTENING THE OIL FILTER CAP .
- Refer to LOWERING THE ENGINE AND DETACHING THE ENGINE BRIDGE .
- Refer to INSTALLING THE ENGINE SUPPORT ARMS ON THE ENGINE MOUNTS ON THE LEFT AND THE RIGHT .
- Refer to ATTACHING THE UNIVERSAL JOINT TO STEERING GEAR .
- Refer to INSTALLING THE REINFORCEMENT STRUT ON THE ENGINE MOUNTING ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE REAR THRUST FIELD .
- Refer to INSTALLING FRONT STIFFENING PLATE .
- Refer to INSTALLING REAR UNDERBODY PROTECTION .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
- Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to TOPPING UP THE MOTOR OIL .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to RESETTING THE TIRE PRESSURE MONITOR .
- Refer to CHECKING ENGINE OIL LEVEL .