Installing exhaust turbocharger

• Replace gasket.

  Parts:  Seals

• Make sure that the part number (1)  remains legible during the assembly of the seal.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Mount gasket (1)  .
• Make sure the seal (1)  is correctly installed on the guide pins.
• If necessary, have the seal (1)  affixed by a support person.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert the exhaust turbocharger (1)  and position it on the trim strip.
• Protect the exhaust turbocharger (1)  from falling.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Mount the reinforcement plate (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace nuts (1)  to (5)  .

  Parts:  Nuts

• Tighten the nuts in the sequence (1)  to (5)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Exhaust manifold to cylinder head
  Flange nut M7 Replace nuts.	1. Joining torque	10 Nm
  	2. Joining torque	10 Nm
  	3. Joining torque	16 Nm
  	4. tightening torque	16 Nm

  Fig 1: Exhaust Turbocharger Nuts Tightening Sequence

  Courtesy of BMW OF NORTH AMERICA, INC.
• Check for correct installation of the seal on the guide pins between the exhaust manifold and the cylinder head.
• If necessary, connect the connector (1)  to the exhaust turbocharger and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Position the heat shield (4)  .
• Tighten down screws (3)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Heat shield to cylinder head
  M8 x 12	Tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Attach heat shield (2)  in marked area.
• Tighten down screw (1)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Heat shield to cylinder head
  M8 x 12	Tightening torque	19 Nm

• Tighten the bolt (1)  on the heat shield (2)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Heat shield to trim strip
  M6 x 12	Tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to ATTACHING THE OIL RETURN LINE FOR THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE OIL FEED LINE FOR THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE COOLANT RETURNING LINE FOR THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE COOLANT FEED LINE FOR THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE COOLANT LINE OF HIGH-TEMPERATURE COOLANT CIRCUIT .
• Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to INSTALLING CATALYTIC CONVERTER .
• Refer to INSTALLING THE COMPLETE EXHAUST SYSTEM .
• Refer to INSTALLING THE REAR DIFFUSER .
• Refer to INSTALLING THE REAR AXLE COVER .
• Refer to IF INSTALLED: INSTALLING THE TORSION STRUT ON THE RIGHT, AND ON THE LEFT WHERE REQUIRED .
• Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
• Refer to INSTALLING THE OXYGEN SENSOR MONITOR .
• Refer to INSTALLING LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING THE CYLINDER HEAD COVER ACOUSTIC COVER .
• Refer to INSTALLING CHARGE AIR LINE .
• Refer to INSTALLING CLEAN AIR PIPE .
• Refer to INSTALLING RESONATOR .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING THE REAR THRUST FIELD .
• Refer to INSTALLING FRONT STIFFENING PLATE .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
• Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .