Install intake plenum

NOTE: RISK OF DAMAGE
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.

Route all cables without abrasions, do not trap and crush.

NOTE: TECHNICAL INFORMATION
Make sure that the connections are locked correctly. The locks must engage audibly.

Replace seals (1).
Parts: Seals

Courtesy of BMW OF NORTH AMERICA, INC.
Clean the contact surface (1).

NOTE: TECHNICAL INFORMATION
Additional coolant can leakage. Make sure that no coolant enters the intake port of the cylinder head.

Feed in and position the intake plenum (A) at the cylinder head.

Tighten screws in the order (1) to (5).

NOTE: Tighten the bolts in 360 degree steps.

TIGHTENING TORQUES SPECIFICATION

Intake plenum to cylinder head
M6	Tightening torque	10 Nm

G14192220

Courtesy of BMW OF NORTH AMERICA, INC.

Connect and lock the coolant feed line (1).
Make sure that the coolant feed line (1) engages audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten down screw (1).

TIGHTENING TORQUES SPECIFICATION

Intake plenum to support
M6X25	Tightening torque	8 Nm

G14191085

Courtesy of BMW OF NORTH AMERICA, INC.

Guide in and Install the wiring harness section (1) for the injectors and ignition coils.

The locks (arrows) must engage audibly.

G14192515

Courtesy of BMW OF NORTH AMERICA, INC.

Guide in and Install the wiring harness section (2) for the injectors and ignition coils.
Secure clamps (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Guide in and install the wiring harness section (2) for sensor system 1.
Secure clamps (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install the tank vent line (1).
Secure the tank vent line (1) to the clamp (2).

G14192214

Courtesy of BMW OF NORTH AMERICA, INC.

Connect connectors (1) and lock.
Make sure the connector (1) engages audibly.
Tighten down screw (2).

TIGHTENING TORQUES SPECIFICATION

Throttle body to holder
M6X25	Tightening torque	8 Nm

G14192211

Courtesy of BMW OF NORTH AMERICA, INC.

Insert and install the coolant hose (2).
Fasten the clamping collar (1) with the special tool 0 495 794 (17 2 050) .
Feed in and install the wiring harness section (3) for sensor system 2.
Make sure that you can hear the locks (arrows) engage.

Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install the tank vent line (2).
Secure the tank vent line (2) to the clamp (3).
Tighten down screw (1).

TIGHTENING TORQUES SPECIFICATION

Tank vent line to intake plenum
Oval-head screw	Tightening torque	3 Nm

G14192207

Courtesy of BMW OF NORTH AMERICA, INC.

Connect connectors (1) and lock.
The connector (1) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install the tank vent line (1).
The locks (arrows) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install the holder (2).
Ensure that the locking mechanism (1) engages audibly.

G14191081

Courtesy of BMW OF NORTH AMERICA, INC.

Replace gasket (1).
Parts: Gasket

Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install charge air line (1).
Tighten screws (arrows).

TIGHTENING TORQUES SPECIFICATION

Charge air line to throttle body
M6	Tightening torque	8 Nm

G14192664

Courtesy of BMW OF NORTH AMERICA, INC.

Connect connectors (1) and lock.
Connect connectors (2) and lock.
Make sure you can hear the connectors (1) and (2) engage.
Secure clamps (3).

G14192663

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE TANK VENT VALVE .
Refer to INSTALLING CONTROL UNIT BRACKET .
Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
Refer to INSTALLING THE DME CONTROL UNIT .
Refer to INSTALLING ACOUSTIC COVER AT REAR .
Refer to INSTALLING THE COWL UPPER PART .
Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
Refer to INSTALLING WINDSHIELD PANEL COVER .
Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
Refer to INSTALLING RESONATOR .
Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
Refer to INSTALLING BATTERY COVER IN TRUNK .
Refer to CONNECTING THE NEGATIVE BATTERY CABLE (12 V BATTERY) .
Refer to ACTIVATE HIGH-VOLTAGE SYSTEM .
Refer to INSTALLING FLAP IN RIGHT LUGGAGE COMPARTMENT TRIM PANEL .
Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
Refer to INSTALLING ACOUSTIC COVER .
Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
Refer to TAKE HOOD OUT OF THE SERVICE POSITION .