Installing the acoustic cover for the oil sump

• Insert and position the acoustic cover (1)  of the oil pan.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .
• Replace the fir tree clip (2)  .

  Parts:  Fir tree clip

• Secure the fir tree clip (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure expanding rivet (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
• Position the transmission oil lines (1)  on the bracket (2)  .

  Make sure that the marks (3)  have been positioned correctly on the holder (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
• Insert and install the holder (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The following step(s) must be performed if the listed component(s) is/are installed.
• Tighten down screw (1)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Holder for transmission oil line
  Screw	Tightening torque	4 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the connector (1)  .
• Make sure the connector (1)  engages audibly.
• Insert and install the positive battery cable (3)  .
• Secure positive battery cable (3)  at the clamp (4)  .
• Tighten the nut (2)  hand-tight.

  Courtesy of BMW OF NORTH AMERICA, INC.

  CAUTION: Improper routing of the positive battery cable. 
  Risk of short circuits! 

  • Route the positive battery cable without abrasions and do not trap.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Attach the positive battery cable (1) correctly  to anit-twist lock (2)  .
• Tighten nut (3)  .

Follow-up work 

• Refer to RAISING FRONT AXLE SUPPORT .
• Refer to TIGHTENING THE SCREWS ON THE LEFT AND RIGHT FRONT AXLE SUPPORT .
• Refer to SECURING THE SPRING STRUT ON THE WISHBONE ON THE BOTTOM LEFT AND RIGHT .
• Refer to SECURING THE WISHBONE ON THE TOP LEFT AND RIGHT ON THE SWIVEL BEARING .
• Refer to REMOVING THE MOBILE LIFTING TABLE .
• Refer to IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
• Refer to SECURING BRAKE HOSE, FRONT RIGHT AND LEFT .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
• Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE STATIONARY HEATING .
• Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
• Refer to FASTENING THE WIRING HARNESS OF THE EPS .
• Refer to INSTALLING THE REINFORCEMENT STRUT ON THE ENGINE MOUNTING ON THE LEFT AND RIGHT .
• Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
• Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
• Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to INSTALLING CLEAN AIR PIPE, TOP .
• Refer to INSTALLING INTAKE SILENCER HOUSING .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
• Refer to INSTALLING THE SIDE HOOD SEAL ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING REAR UNDERBODY PROTECTION .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .