Remove counterbalance shafts

Preliminary work 

• Refer to REMOVING ENGINE .
• Refer to INSTALLING THE ENGINE ON THE ASSEMBLY STAND .
• Refer to RELEASING THE OIL DRAIN PLUG
• Refer to TIGHTENING THE OIL DRAIN PLUG
• Refer to REMOVING ALL SPARK PLUGS .
• Refer to REMOVING THE HIGH PRESSURE LINE BETWEEN THE HIGH PRESSURE PUMP AND THE RAIL .
• Refer to REMOVING HIGH PRESSURE PUMP .
• Refer to REMOVING THE RAIL WITH INJECTORS .
• Refer to REMOVING BOTH ACTUATORS .
• Refer to REMOVING THE CYLINDER HEAD COVER .
• Refer to REMOVING TANK VENT VALVE .
• Refer to REMOVING THE INTAKE PLENUM .
• Refer to REMOVING THE HEAT SHIELD AT THE CYLINDER HEAD .
• Refer to REMOVING THE OIL RETURN LINE FOR THE EXHAUST TURBOCHARGER .
• Refer to REMOVING THE COOLANT RETURN LINE FOR THE EXHAUST TURBOCHARGER .
• Refer to REMOVING THE COOLANT FEED LINE FOR THE EXHAUST GAS TURBOCHARGER .
• Refer to BLOCKING ENGINE IN TDC FIRING POSITION .
• Refer to REMOVING CHAIN TENSIONER .
• Refer to RELEASING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
• Refer to RELEASING VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
• Refer to REMOVING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
• Refer to REMOVING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
• Refer to REMOVING INTAKE ADJUSTER .
• Refer to REMOVING EXHAUST CAMSHAFT ADJUSTER .
• Refer to REMOVING THE TEST GAUGES FOR SECURING THE CAMSHAFTS .
• Refer to REMOVING THE CYLINDER HEAD .
• Refer to REMOVING THE CYLINDER HEAD GASKET .
• Refer to REMOVING THE VIBRATION DAMPER .
• Refer to REMOVING FLYWHEEL .
• Refer to REMOVING THE ACOUSTIC COVER OF THE OIL SUMP .
• Refer to REMOVING OIL SUMP .
• Refer to REMOVING REAR TIMING CASE COVER .
• Refer to REMOVING OIL VACUUM PUMP .
• Refer to REMOVING THE OIL DEFLECTOR .

• Remove both sealing caps (1) with a suitable tool (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Rotate the crankshaft to the lower dead center of the first cylinder  .
• Mount the special tool 2 288 054  and abut the screws (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The description is for one component only. The procedure is identical for all further components.
• Makes sure that the special tool 2 288 054  fits in the guides (1) of the counterbalance shafts (2) correctly.
• If necessary slightly rotate the crankshaft.
• Tighten special tool 2 288 054  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Special tool 2 288 054 to crankshaft
  	tightening torque	20 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen screws (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen screws (1).
• Guide the special tool 2 288 054  out and remove.

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: The description is for one component only. The procedure is identical for all further components.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Screw the special tool 2 458 114  into the gear of the counterbalance shaft and counter support with an open-end wrench (1).
  NOTE: The gears are pressed onto the counterbalance shaft with a taper and can only be released with the special tool 2 458 114  .
• Release the counterbalance shaft by screwing in the screw (2) of the special tool 2 458 114  from the gear.
• Carefully remove the counterbalance shafts (1) from the crankcase towards the front.

  The counterbalance shafts (1) must not be in the bearing positions, as this might damage the crankcase.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Check all needle bearings of the counterbalance shafts (1) for damage and replace if necessary.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Remove the gear (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Remove the gear (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen nut (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Remove the gear (1).

  Courtesy of BMW OF NORTH AMERICA, INC.