Mount and secure the complete front axle

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW X2, 2022 BMW X2, 2021 BMW X2, 2020 BMW X2, and 2019 BMW X2. However, it is still accessible from the selected car via links, so may be relevant.

Remove the sealing (1).
Clean surface on steering gear.
Replace the seal (1).
Parts: Seal
Position the seal (1) and glue it on.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: RISK OF DAMAGE
Failure to comply with the specification .
Component damage .

All specifications must be observed and complied with.

When lowering and raising the front axle support, make sure that the torsion bar (1) of the electromechanical steering gear (EPS) in the area (2) does not collide with the firewall!

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Collision with the firewall may result in damage to the electromechanical steering gear (EPS)!

Position front axle support.
Bend underbody panelings in the areas (3) to one side.
Raise front axle support.
When raising, insert charge air cooler into the rubber mount of the charge air cooler on cross member.
Replace screws (1) and (2).

Parts: Screws

Tighten the screws (1).

TIGHTENING TORQUE SPECIFICATIONS

Rear end of front axle support to body
Screw M14 Replace screw.	Tightening torque	175 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten the screws (2).

TIGHTENING TORQUE SPECIFICATIONS

Front axle support, front to body
M12 screw Replace screw.	Tightening torque	108 Nm

If necessary, tighten the screws in the areas (3).

TIGHTENING TORQUE SPECIFICATIONS

Underbody protection to body
screw	Tightening torque	3 Nm

Release the special tool 0 496 080 (33 5 206) from the special tool 0 495 817 (31 5 251) .
Lower the universal jack 0 490 133 (00 2 030) with the special tool 0 495 817 (31 5 251) and set it aside.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Perform the steps on the right and left side.

Position the track rod (2) on the swivel bearing.

Replace nut (1).
Parts: Nut
Tighten nut (1).

TIGHTENING TORQUE SPECIFICATIONS

Tie rod end to swivel bearing
M14 Replace nut.	Tightening torque	175 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Perform the steps on the right and left side.

Position the wishbone (3) on the swivel bearing.
Replace screw (2) and nut (1).
Parts: Bolt, nut
Insert screw (2).
Position nut (1).
Tighten down screw (2).

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUE SPECIFICATIONS

Wishbone to swivel bearing
M10 Exclusively use the screw to tighten! Replace screw and nut.	Tightening torque	56 Nm

Follow-up work

Refer to SECURING THE MOUNTED PART ON THE FRONT AXLE SUPPORT .
Refer to CONNECTING PURGE AIR LINE .
Refer to ATTACHING CONNECTOR AT STEERING GEAR .
Refer to FASTENING THE RUBBER MOUNT ON THE FRONT AXLE SUPPORT .
Refer to SECURING THE ANTI-ROLL BAR ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR LINK .
Refer to WITH RIGHT INSTALLATION: FASTENING THE CABLE FOR THE RIDE HEIGHT SENSOR .
Refer to INSTALLING FRONT LEFT AND RIGHT WHEEL ARCH COVER .
Refer to IF INSTALLED: INSTALLING UNDERBODY PROTECTION AT REAR .
Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
Refer to REMOVING COOLANT RADIATOR ATTACHMENT ON THE LEFT AND RIGHT .
Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
Refer to DISCONNECTING ALL BATTERY GROUND LEADS .