Install the acoustic cover for the oil sump

Install the acoustic cover for the oil sump 

• Install the acoustic cover (2)  toward the front and top and secure it with the expanding rivets (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Fasten all expanding rivets (2)  and the christmas tree clip (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Thread in terminal 50 (4)  and fasten it with the nut (5)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Terminal 50 to starter motor
  M6	Tightening torque	7 Nm

• Insert the positive battery cable (1)  and attach it correctly to the anti-twist lock (2)  .
• Tighten nut (3)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Battery positive lead to starter
  M8	Tightening torque	13.5 Nm

• Attach terminal 50 (4)  to the clip (6)  .

Follow-up work 

• Refer to IF INSTALLED ON LEFT: POSITION SPRAY GUARD .
• Refer to RAISING FRONT AXLE SUPPORT .
• Refer to TIGHTENING THE BOLTS ON THE FRONT AXLE SUPPORT .
• Refer to SECURING THE SPRING STRUT TO THE BOTTOM WISHBONE .
• Refer to SECURING THE TOP WISHBONE ON THE SWIVEL BEARING .
• Refer to REMOVING THE MOBILE LIFTING TABLE .
• Refer to ATTACHING COOLANT HOSES TO FRONT SUBFRAME .
• Refer to SECURING THE RIGHT AND LEFT OUTPUT SHAFTS ON THE WHEEL BEARING .
• Refer to IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
• Refer to SECURING BRAKE HOSE, FRONT RIGHT AND LEFT .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
• Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE STATIONARY HEATING .
• Refer to IF INSTALLED ON LEFT: INSTALLING SPRAY GUARD .
• Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
• Refer to IF INSTALLED: CONNECTING THE VACUUM HOSE OF THE ENGINE MOUNTING ON THE FRONT AXLE SUPPORT .
• Refer to LOWERING THE ENGINE AND DETACHING THE ENGINE BRIDGE .
• Refer to INSTALLING THE ENGINE SUPPORT ARMS ON THE ENGINE MOUNTS ON THE LEFT AND THE RIGHT .
• Refer to ATTACHING THE UNIVERSAL JOINT TO STEERING GEAR .
• Refer to INSTALLING THE REINFORCEMENT STRUT ON THE ENGINE MOUNTING ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE REAR THRUST FIELD .
• Refer to INSTALLING FRONT STIFFENING PLATE .
• Refer to INSTALLING REAR UNDERBODY PROTECTION .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
• Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to RESETTING THE TIRE PRESSURE MONITOR .