Installing the hydraulic valve for the oil pressure control
- Check the O-ring (1) for damage.
- If necessary, replace the hydraulic valve.
- Install the hydraulic valve (2) .
- Tighten down screw (1)
.TIGHTENING TORQUE SPECIFICATIONS
Hydraulic valve to crankcase M6x18 Tightening torque 8 Nm - Connect connector (1)
.
- Tighten the transmission bolt (1)
.TIGHTENING TORQUE SPECIFICATIONS
Transmission to engine M12x 100 Tightening torque 66 Nm
Follow-up works
- Refer to INSTALLING THE TRANSMISSION OIL COOLER .
- Refer to INSTALLING THE INTAKE PLENUM .
- Refer to FASTENING CHARGE AIR LINE TO THE THROTTLE BODY .
- Refer to INSTALLING THE TANK VENT VALVE .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING THE SOUND INSULATION ON THE BULKHEAD UPPER PART CENTER .
- Refer to INSTALLING TENSION STRUT ON SPRING STRUT DOME .
- Refer to INSTALLING THE HOLDER FOR THE DIGITAL MOTOR ELECTRONICS-CONTROL UNIT .
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to CONNECTING THE CONNECTOR WITH THE DME CONTROL UNIT AND THE POWER DISTRIBUTION BOX (PDM) .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR OF THE LOW-TEMPERATURE COOLANT CIRCUIT .
- Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR .
- Refer to INSTALLING THE PROTECTIVE PLATE FOR THE FUEL LINES .
- Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
- Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLER DEVICE .
- Refer to FILLING THE LOW-TEMPERATURE COOLANT CIRCUIT WITH THE VACUUM FILLER DEVICE .
- Refer to BLEEDING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
- Refer to BLEEDING THE LOW-TEMPERATURE COOLING CIRCUIT .
- Refer to CHECKING/TOPPING UP OIL LEVEL IN AUTOMATIC TRANSMISSION .
- Refer to INSTALLING THE SUPPORT FOR THE UNDERBODY PROTECTION .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
- Check the O-ring (1) for damage.
- If necessary, replace the hydraulic valve.
- Install the hydraulic valve (2) .
- Tighten down screw (1)
.TIGHTENING TORQUE SPECIFICATIONS
Hydraulic valve to crankcase M6x18 Tightening torque 8 Nm - Connect connector (1)
.
- Tighten the transmission bolt (1)
.TIGHTENING TORQUE SPECIFICATIONS
Transmission to engine M12x 100 Tightening torque 66 Nm
Follow-up works
- Refer to INSTALLING FULL-FLOW OIL FILTER .
- Refer to TIGHTENING THE OIL DRAIN PLUG .
- Refer to TIGHTENING THE OIL FILTER CAP AS NEEDED .
- Refer to FILLING IN ENGINE OIL .
- Refer to CONNECTING THE COOLANT FEEDER HOSE TO THE CONNECTING BRACKET .
- Refer to INSTALLING THE AUXILIARY COOLANT PUMP .
- Refer to INSTALLING THE INTAKE PLENUM .
- Refer to FASTENING CHARGE AIR LINE TO THE THROTTLE BODY .
- Refer to INSTALLING THE TANK VENT VALVE .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING SOUND INSULATION AT THE CENTER OF THE BULKHEAD UPPER PART .
- Refer to INSTALLING TENSION STRUT ON SUSPENSION STRUT TOWER .
- Refer to INSTALLING THE HOLDER FOR THE DIGITAL MOTOR ELECTRONICS-CONTROL UNIT .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to CONNECTING THE CONNECTOR WITH THE DME CONTROL UNIT AND THE POWER DISTRIBUTION BOX (PDM) .
- Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR OF THE LOW-TEMPERATURE COOLANT CIRCUIT .
- Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR .
- Refer to FILLING THE LOW-TEMPERATURE COOLANT CIRCUIT WITH THE VACUUM FILLER DEVICE .
- Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLER DEVICE .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING COVER FOR THE DME CONTROL UNIT .
- Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
- Refer to BLEEDING THE LOW-TEMPERATURE COOLING CIRCUIT .
- Refer to BLEEDING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
- Refer to CHECKING ENGINE OIL LEVEL .
- Refer to INSTALLING THE SUPPORT FOR THE UNDERBODY PROTECTION .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .