18 32 060 Removing and installing/replacing catalytic converters for cylinders 5-8 (N63) (X6 xDrive 50i)

Necessary preliminary tasks: 

• Remove upper HEAT SHIELD .
• Remove the UNITS COMPARTMENT PARTITION WALL .
• Remove EXHAUST SYSTEM .
• Remove VACUUM PUMP .
• Remove left and right monitoring sensor. Refer to 11 78 540 REPLACING LEFT MONITORING SENSOR (N63O1) REP-REP-RAF1511N63O1-1178540 - V.4 (X6 XDRIVE 50I) and 11 78 543 REPLACING RIGHT MONITORING SENSOR (N63O1) REP-REP-RAF1511N63O1-1178543 - V.4 (X6 XDRIVE 50I) .

Release screw (1) from heat shields (2) and (3).

Screw (1) is located between the catalytic converters.

Tightening torque 18 31 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Release screw (1) on heat shield at bottom right.

Tightening torque 18 31 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Release screw (1) on right heat shield.

Tightening torque 18 31 3AZ .

Unclip and remove the right heat shield.

Courtesy of BMW OF NORTH AMERICA, INC.

Release screw (1) on heat shield at bottom left.

Tightening torque 18 31 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Release screw (1) on right left shield.

Tightening torque 18 31 3AZ .

Unclip and remove the heat shield (2) on the left.

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1).

Tightening torque 18 32 2AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1).

Tightening torque 18 32 2AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Loosen screws (1) on the catalytic converter cylinders 1 - 4 on the back of the cylinder head.

Tightening torque 18 32 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) on catalytic converter, cylinders 5-8, rear, at cylinder head.

Tightening torque 18 32 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Loosen screws (1) on the catalytic converter cylinders 1 - 4 on the back of the cylinder head.

Tightening torque 18 32 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) on catalytic converter, cylinders 5-8, rear, at cylinder head.

Tightening torque 18 32 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) and (3).

Tightening torque 18 32 1AZ .

Remove and replace clamps (2) and (4).

Installation note: 

Clamps must be installed with the screws toward the inside (graphic). Otherwise, a top heat shield can no longer be installed.

Courtesy of BMW OF NORTH AMERICA, INC.

Installation note: 

If you can see a gap between the ends of the V-band clamps, release and then repeat the screw connection.

Tightening torque 18 32 1AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Installation note: 

If the ends of the V-band clamps are positioned under each other, release and then repeat the screw connection.

Tightening torque 18 32 1AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

1. Remove catalytic converter for cylinders 1 - 4 (2).
2. Remove catalytic converter for cylinders 5-8 (1).

   Courtesy of BMW OF NORTH AMERICA, INC.

Installation note: 

Graphic shows the engine removed.

Replace the seals (1) on the exhaust turbocharger.

Courtesy of BMW OF NORTH AMERICA, INC.

Assemble engine.

Check exhaust system for leak tightness.