28 60 514 Replacing Mechatronics (GS7D36SG)

WARNING: This page does not describe the selected car, but rather 50 other vehicles, including the 2016 BMW M5, 2016 BMW ActiveHybrid 5, 2016 BMW 550i xDrive, 2016 BMW 550i, and 2016 BMW 535i xDrive. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: When replacing mechatronics:

Import present transmission data into new mechatronics via ISTA/P .

IMPORTANT: It is essential to adhere to conditions of absolute cleanliness.
Any dirty parts must be cleaned before the hydraulic cap is loosened.
After completion of work, check GEARBOX OIL LEVEL .
Use only the approved transmission oil .
Failure to comply with this instruction will result in serious damage to the twin-clutch gearbox.

IMPORTANT: Read and comply with notes on PROTECTION AGAINST ELECTROSTATIC DISCHARGE (ESD PROTECTION) .

Necessary preliminary tasks:

Read out transmission data of mechatronics to be replaced via ISTA/P .
Remove TWIN-CLUTCH GEARBOX .

Place twin clutch transmission on a suitable surface.

To prevent the transmission oil from spilling out, make sure that the hydraulic cap points upward.

Remove HYDRAULIC CAP (1).

Fig 1: Hydraulic Cap

Courtesy of BMW OF NORTH AMERICA, INC.

Ensure correct installation position.

Press holder (2) together from right and release cable (1).

Installation note:

Replace holder.

Retaining lugs must point to the right.

If fitted: Pull out CPA pin (7) to second locking position.

Release connector lock (6) and at same time detach connector (3) from retaining tabs (5) towards right.

Fig 2: Mechatronics, CPA Pin, Cable And Connector

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Bridge (4) of connector must not break.

Wiring harness must be replaced if bridge breaks.

CPA (1) in second locking position.

Installation note:

Press CPA pin down until it is flush with the housing.

Fig 3: CPA

Courtesy of BMW OF NORTH AMERICA, INC.

Fig 4: Automatic Transmission Valve Body (Mechatronics) Screws Tightening/Loosening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Place mounting template over mechatronics.

Open screws 1-20.

NOTE: Replace screws 1-12.

Screws 13-20 remain captive on module.

Remove mounting template.

Lift mechatronics out of housing.

Remove metal bead gasket.

Fig 5: Removing Metal Bead Gasket

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Check the installation position of the centering pins (1).
The centering pins (1) of the mechatronics remain in the housing.

Fig 6: Mechatronics Centering Pins

Courtesy of BMW OF NORTH AMERICA, INC.

The new mechatronics are supplied with the shift piston in neutral position as illustrated.

Fig 7: Mechatronics Unit

Courtesy of BMW OF NORTH AMERICA, INC.

In the gearbox, the gearshift rods have to be set to the neutral position '(N) as shown here before the new mechatronics are installed.

Fig 8: Gear Neutral Position

Courtesy of BMW OF NORTH AMERICA, INC.

Installing mechatronics:

Install a new metal bead gasket.

Install mechatronics.

Fit mounting template.

Fig 9: Automatic Transmission Valve Body (Mechatronics) Screws Tightening/Loosening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Adhere without fail to the screwing sequence indicated on the template.

The screw length can be checked by means of the insert pockets shaped in the template.

Insert screws in sequence 1-12 and pre-tighten to 2 Nm.

Tighten down screws 1-12 to tightening torque and angle of rotation:

Type	Thread	Tightening specification	Measure
GS7D36SG	M5x30	Jointing torque: Torque angle:	3 Nm +50 °
M5X35		Jointing torque: Torque angle:	3 Nm +50 °
M5X50		Jointing torque: Torque angle:	3 Nm +50 °
M5X75		Jointing torque: Torque angle:	3 Nm +90 °

Tighten down screws in sequence 13-20 to 5 Nm.
Remove mounting template.