00 .. . BMW service-inspection (petrol/gasoline vehicles): Notes
WARNING: This page is about a different car, the 2010 BMW X3, 2009 BMW X3, 2008 BMW X3, and 2007 BMW X3. However, it is still accessible from the selected car via links, so may be relevant.
IMPORTANT:
The operations set out below always refer to the maximum possible scope of a service-inspection.
The exact scope of the vehicle in question must be printed out with the vehicle identification number from the KSD CD.
The exact scope of the vehicle in question must be printed out with the vehicle identification number from the KSD CD.
Body / electrical system
- Check lighting system: instrument and indication field lighting, heater fan, signal horn, headlight flasher and hazard warning lights, see 00 00 ... Checking lighting system
- Seat belts: check condition of belt strap, function of inertia reel mechanism, locking reel, belt buckle, see 00 00 ... Seat belts: checking condition of belt strap, function of inertia reel mechanism, locking reel, belt buckle
- Battery:
- Check acid level, charge state (magic eye)
- If necessary: Charge battery, see 00 00 ... Battery: checking acid level, topping up with distilled water if necessary. If necessary, recharge battery.
- Heating/air conditioning: change microfilter / carbon canister, see 00 00 ... Heating/air conditioning: replacing microfilter/carbon canister (shorten replacement interval accordingly in event of larger buildup of dust)
- Body and underbody: check for corrosion and damage-except cavities, see 00 00 ... Body and underbody: checking for corrosion and damage - except cavities
Engine compartment
- Diagnostic brief test , see 00 00 ... Diagnostic brief test
- In event of fault memory entry "54C6" change transfer case oil , see 00 00 ... Oil change in transfer case
- Change engine oil and oil filter , see 00 00 ... Changing engine oil and oil filter
- Replace spark plugs , see 00 00 ... Replacing spark plugs
- Coolant hoses: visually inspect for leaks, check coolant level and concentration, top up if necessary Caution! Replace coolant at least every 3 years, see 00 00 ... Coolant hoses: visual inspection for leaks. Checking coolant level and concentration, topping up if necessary
- Reset service interval indicator according to factory specifications, see 00 00 ... Resetting service interval indicator according to factory specifications
- Windscreen washer system and intensive cleaning system: check fluid level, top up if necessary, see 00 00 ... Windscreen washer system and intensive cleaning system: checking fluid level, topping up if necessary
- Power steering/ride-height control: visual inspection for leaks, check fluid level, top up fluid if necessary, see 00 00 ... Power steering/ride-height control: visual inspection for leaks, checking fluid level, topping up fluid if necessary
- caution Change brake fluid in accordance with service interval indicator , no later than every 2 years, see 00 00 ... Changing brake fluid
- Air cleaner: Replace air cleaner element, see 00 00 ... Air cleaner: replacing air cleaner element (shorten replacement interval accordingly in event of larger buildup of dust)
Chassis / suspension area
- Front and rear disc brake pads:
- check pad thickness with measuring gauge 00 00 ... Front and rear brake linings: checking lining thickness with measuring gauge. If linings are replaced: cleaning brake shafts, checking brake disk thickness and surface, applying grease to wheel centering on alloy wheels. If rear linings are replaced: checking parking brake linings
- If pads are replaced: Clean brake ducts. Brake discs: Check surface and thickness. If replacing at rear: check parking brake linings. Grease wheel centering on light alloy wheels.
- Check steering for play . Steering tie rods and axle joints, steering gear, sleeves and flexible disc: check condition, see 00 00 ... Steering components: checking for zero clearance, leaks, damage and wear
- Underbody incl. all visible components : check for damage, leaks, corrosion, see 00 00 ... Underbody incl. all visible components: checking for damage, leaks, corrosion
- Brake lines and connections: visual inspection for leaks, damage and correct position, see 00 00 ... Brake lines and connections: visual inspection for leaks, damage and correct position
- Check handbrake lever travel , adjust according to setting specifications if necessary, see 00 00 ... Checking handbrake lever travel, adjusting according to setting specifications if necessary
- Tires:
- Check pressure, correct if necessary (including spare wheel). Check external condition (left/right), check tread depth and pattern
- If level of wear is not uniform, measure and correct wheel alignment after consulting with customer, see 00 00 ... Tires: checking inflation pressure, correcting if necessary (incl. spare wheel), checking external condition, tread depth, pattern. In event of nonuniform wear, carry out measurement and correction of wheel alignment