Valve Stem Seals, Removing And Installing, Cylinder Head Installed

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2023 Audi SQ8, 2023 Audi RS Q8, 2022 Audi SQ8, 2022 Audi RS Q8, and 2021 Audi SQ8. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Puller - Valve Seal:3364

Fig 1: Identifying Puller - Valve 3364
Courtesy of AUDI OF AMERICA, LLC
Seal Installer - Valve Stem:3365

Fig 2: Identifying Seal Installer - Valve Stem 3365
Courtesy of AUDI OF AMERICA, LLC
Valve Cotter Tool Kit:VAS 5161A with the Valve Keeper Tool Kit - Compression Stud :VAS 5161/10

Fig 3: Valve Keeper Tool Kit VAS5161A
Courtesy of AUDI OF AMERICA, LLC
Guide Plate V6 TFSI: VAS 5161A/38 , not illustrated
Spark Plug Socket Adapter 3/8" :VAS 6919 , not illustrated
Wrench - 21mm:T40263

Fig 4: Identifying Wrench - 21mm
Courtesy of AUDI OF AMERICA, LLC
Adapter:T40314

Fig 5: Adapter T40314
Courtesy of AUDI OF AMERICA, LLC
Two M8 Bolts (part number N 108 063 01)

Guide Plate V6 TFSI: VAS 5161A/38 , Preparing

Courtesy of AUDI OF AMERICA, LLC

-- The Guide Plate V6 TFSI: VAS 5161A/38 must be modified for cylinders 4 and 8.

-- Two M8 bolts (part number N 108 063 01) -1- must be installed in the Guide Plate V6 TFSI: VAS 5161A/38 -2- from above.

Courtesy of AUDI OF AMERICA, LLC

The bolts may extend a maximum of 5 mm underneath.
The projecting ends of the bolts will be positioned on the oil channels -3-.

Depending on the installation scenario, pay attention to using the holes and secure the Guide Plate V6 TFSI: VAS 5161A/38 using the M5x40 bolts that are provided.

Courtesy of AUDI OF AMERICA, LLC
For work on the other cylinders, the bolts can remain installed in the Guide Plate V6 TFSI: VAS 5161A/38 .
There are four holes -a, b, c, d- in the Guide Plate V6 TFSI: VAS 5161A/38 for securing on the cylinder head.

Procedure for valve stem seals cylinder 4 and 8 on the intake side:

-- For the removal of the valve stem seals from cylinder 4 and 8 on the intake side: remove the engine with the transmission and subframe on the removed lock carrier downward. Refer to Engine, Removing and Installing .

Procedure for valve stem seals cylinder 1 and 5 on the intake side, Audi RSQ8 / SQ8 / SQ7:

-- For the removal of the valve stem seals from cylinder 1 and 5 on the intake side: remove the engine with the transmission and subframe on the removed lock carrier downward. Refer to Engine, Removing and Installing .

Procedure for all:

-- Remove the applicable camshaft housing. Refer to CAMSHAFT HOUSING, REMOVING AND INSTALLING .

-- Mark the allocation of the roller rocker lever and the hydraulic lifter so they can be installed again.

-- Remove the roller rocker lever with the hydraulic lifter and place them on a clean surface.

-- Remove all spark plugs using the Spark Plug Socket Adapter 3/8":VAS 6919 .

-- Turn the crankshaft using the Wrench - 21mm:T40263 and Adapter:T40314 -arrow- until the pistons of the corresponding cylinder are in "bottom dead center (BDC)".

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Risk of damaging camshaft timing chain.

- If the crankshaft is turned the camshaft timing chains must be guided.

-- Align the Valve Keeper Tool Kit - Guide Plate V6/V8 TFSI:VAS 5161A/38 on the cylinder head while paying attention to the -A/E- markings:

Courtesy of AUDI OF AMERICA, LLC

A - Exhaust side

E - Intake side

-- Tighten the bolts -arrows- for the Guide Plate V6 TFSI: VAS 5161A/38 to 9 Nm.

TIP

For cylinders 4 and 8, the Guide Plate V6 TFSI: VAS 5161A/38 can only be secured with one bolt. Therefore, to increase process safety, the two M8 bolts must be mounted in the guide plate. These bolts will be used to prevent rotation.

-- Insert the Valve Cotter Tool Kit - Punch :VAS 5161/3A in the guide plate and loosen the stuck valve retainers with a plastic mallet.

-- Install the Valve Keeper Tool Kit - Compression Stud for VAS 5161/9 :VAS 5161/10 in the Valve Keeper Tool Kit - Guide Plate V6/V8 TFSI:VAS 5161A/38 hand-tight.

Courtesy of AUDI OF AMERICA, LLC

-- Install the Valve Cotter Tool Kit - Adapter:T40012/1 with sealing ring in the corresponding spark plug thread and tighten hand-tight.

-- Connect the adapter to the compressed air using a commercially available intermediate piece -arrow- and give steady pressure.

Minimum pressure: 6 bar (87.02 psi)

CAUTION:

Risk of damaging the valves due to a pressure decrease in the cylinder.

- Never remove the guide plate or the compression stud.

- Keep the pressure in the cylinder at a minimum of 6 bar (87.02 psi).

-- Install the Retainer :VAS 5161/6 with the Guide Forks M6/M8 with Threaded Studs :VAS 5161/5 in the guide plate.

Courtesy of AUDI OF AMERICA, LLC

-- Insert the Valve Keeper Tool Kit - Assembly Cartridge :VAS 5161/8 A into the opening above the valve spring that is to be removed.

-- Engage the Valve Keeper Tool Kit - Pressure Fork :VAS 5161/2 at the engaging device : VAS 5161/6 and press the installation cartridge downward.

-- At the same time, turn the installation cartridge knurled bolt -arrow- right until points engage in the valve keepers.

-- Move the knurled bolt left and right slightly. This presses the valve keepers apart and captures them in the assembly cartridge.

The knurled bolt slides all the way in the assembly cartridge.

-- Release the pressure fork : VAS 5161/2 and remove the assembly cartridge : VAS 5161/8A .

For the reinstallation of the valve springs for the exhaust valve mark the installation position with pant.

-- Remove the valve spring and the valve spring retainer.

Valve Stem Seals, Replacing:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the valve stem seal using the Puller - Valve Seal:3364 .

If the Puller - Valve Seal:3364 cannot be used on some valve stem seals due to a limited amount of space, proceed as follows:

Fig 6: Driving Out Roll Pin

Courtesy of AUDI OF AMERICA, LLC

-- Remove the roll pin -arrow- on the puller with a drift and remove the impact puller attachment.

-- Position the lower section of the Puller - Valve Seal:3364 on the valve stem seal.

Courtesy of AUDI OF AMERICA, LLC

-- Secure the puller with the drift or pin punch -1-.

-- Position the extractor lever on the puller and remove the valve stem seal -arrow-.

So that the new valve stem seal -2- is not damaged during installation, mount the Guide Sleeve -1- on the valve stem.

Courtesy of AUDI OF AMERICA, LLC

-- Lightly oil the valve stem seal sealing lip.

-- Insert the valve stem seal in the Seal Installer - Valve Stem:3365 and carefully press on the valve guide all the way.

-- Remove the Assembly Sleeve.

If the valve keepers were removed from the assembly cartridge, they must then be inserted into the Valve Keeper Tool Kit - Valve Insertion Device :VAS 5161/18 .

Fig 7: Identifying Installation Cartridge VAS 5161/8

Courtesy of AUDI OF AMERICA, LLC

The large diameter of the valve keepers point upward.

-- Press the cartridge from above onto the insertion device and valve keepers.

-- Insert the valve spring and the valve spring retainer.

Intake valve installation position. Refer to Figure.
Exhaust valve installation position. Refer to Figure.

-- Insert the Valve Keeper Tool Kit - Assembly Cartridge :VAS 5161/8A back into the Valve Keeper Tool Kit - Guide Plate V6/V8 TFSI:VAS 5161A/38 .

Courtesy of AUDI OF AMERICA, LLC

-- Press the Valve Keeper Tool Kit - Pressure Fork with Lever for Assembly Cartridge :VAS 5161/2 down and pull the knurled screw -arrow- up while turning left and right. This inserts the valve retainers.

-- Release the Pressure Fork with Lever for Assembly Cartridge :VAS 5161/2 with the knurled thumb screw still pulled.

-- Repeat the procedure on each valve.

Assembling

Assemble in the reverse order of removal.

-- Make sure all the roller rocker levers lie correctly on the ends of the valve stems and are clipped onto the respective hydraulic lifters.

-- Install the spark plugs. Refer to OVERVIEW - IGNITION SYSTEM .

-- Install the camshaft housing. Refer to CAMSHAFT HOUSING, REMOVING AND INSTALLING .

-- If removed: install the engine with the transmission and subframe with the lock carrier removed. Refer to Engine, Removing and Installing .