Axle Alignment Specified Values

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Audi SQ5, 2024 Audi Q5 e, 2024 Audi Q5, 2023 Audi SQ5, and 2023 Audi Q5 e. However, it is still accessible from the selected car via links, so may be relevant.

Conditions

The settings specified apply to the curb weight position (refer to Dimension Overview ) or the standard vehicle height of the vehicle (refer to Dimension Overview ). To determine the curb weight position or the standard vehicle height, the dimension -a- between the center of the wheel and the lower edge of the fender/wheel housing is determined.

Fig 1: Determining Height Dimension -a-
Courtesy of AUDI

Front Axle

1BL

1BQ. Refer to AXLE ALIGNMENT SPECIFIED VALUES.

1BA/1BV

Version

Steel spring

Camber

Adjustment value

-28' ± 23'

- 49' ± 23'

-28' ± 23'

Check value

-28' ± 25'

-49' ± 25'

-28' ± 25'

Maximum permissible difference between both sides

30'

Toe-in per wheel

Adjustment value

10' ± 5'

Check value

+ 10' ± 7'

Total toe-in

+20' ± 10'

Toe difference angle at 20°. Refer to ⁽¹⁾

-1°30'36" ± 30'

-1°30' ± 30'

-1°30'36"± 30'

Outer wheel steering angle at maximum steering angle

33°12' ± 1°30'

33°9'36" ± 1°30'

33°12' ± 1°30'

Inner wheel steering angle at maximum steering angle

39°31'12' ± 1°30'

39°27' ± 1°30'

39°31'12' ± 1°30'

⁽¹⁾	Wheel stop on outer wheel is reduced by this amount. It can also be indicated negatively in the wheel alignment computer depending on manufacturer.

Front Axle

1BA with High-Voltage System

2MF. Refer to AXLE ALIGNMENT SPECIFIED VALUES

1BK

Version

Steel spring

Air Spring

Camber

Adjustment value

-29' ± 23'

-45' ± 23'

Check value

-29' ± 25'

-45' ± 25'

Maximum permissible difference between both sides

30'

Toe-in per wheel

Adjustment value

10' ± 5'

Check value

+ 10' ± 7'

Total toe-in

+20' ± 10'

Toe difference angle at 20°. Refer to ⁽¹⁾

-1°30'36" ± 30'

-1°30' ± 30'

Outer wheel steering angle at maximum steering angle

33°12' ± 1°30'

33°10'12" ± 1°30'

Inner wheel steering angle at maximum steering angle

39°31'12" ± 1°30'

39°27'36" ± 1°30'

⁽¹⁾	Wheel stop on outer wheel is reduced by this amount. It can also be indicated negatively in the wheel alignment computer depending on manufacturer.

Front Axle

1BK with High-Voltage System

2MB

Version

Air Spring

Camber

Adjustment value

- 49' ± 23'

Check value

-49' ± 25'

Maximum permissible difference between both sides

30'

Toe-in per wheel

Adjustment value

10' ± 5'

Check value

+ 10' ± 7'

Total toe-in

+20' ± 10'

Toe difference angle at 20°. Refer to ⁽¹⁾

-1°30' ± 30'

Outer wheel steering angle at maximum steering angle

33°10'12" ± 1°30'

33°9' ± 1°30'

Inner wheel steering angle at maximum steering angle

39°27'36" ± 1°30'

39°27' ± 1°30'

⁽¹⁾	Wheel stop on outer wheel is reduced by this amount. It can also be indicated negatively in the wheel alignment computer depending on manufacturer.

Electronic damping

Rear Axle	All Suspension Types	All Suspension Types
Version	Steel spring	Air Spring
Camber	- 50' ± 25'	- 50' ± 25'
Maximum permissible difference between both sides	30'	30'
Toe-in	+20' ± 10'	+20' ± 10'
Maximum permissible deviation in direction of travel relative to vehicle longitudinal axis	10'	10'