Overview - Engine Compartment Lid

Fig 1: Exploded View Of Engine Compartment Lid

Courtesy of AUDI OF AMERICA, LLC

Rear Lid
- Removing and Installing. Refer to REAR LID, REMOVING AND INSTALLING .
- Adjusting. Refer to REAR LID, ADJUSTING .
Nut
- Component Location Overview. Refer to COMPONENT LOCATION OVERVIEW - CONTROLS IN LUGGAGE COMPARTMENT
Adapter
- For Release Button in Rear Lid Handle -E234-
- Component Location Overview. Refer to COMPONENT LOCATION OVERVIEW - CONTROLS IN LUGGAGE COMPARTMENT
Release Button In Rear Lid Handle -E234-
- Component Location Overview. Refer to COMPONENT LOCATION OVERVIEW - CONTROLS IN LUGGAGE COMPARTMENT
Balance Weight
- Equipped on some models
Nut
- 21 Nm
- Quantity: 2
Rear Lid Control Head -EX58- with Rear Lid Lock Button in Luggage Compartment -E406-
- Removing and installing. Refer to REAR LID CONTROL HEAD -EX58-, REMOVING AND INSTALLING .
Plug
Mount
- Right
- With ball pin
Cover
- No replacement part
Latch
- Rear Lid Lock Unit -VX25-
- With Rear Lid Central Locking System Motor -V53-, Lock Pawl Contact Switch -F443-, equipped on some models: Rear Lid Contact Switch -F111-
- Removing and Installing. Refer to LATCH, REMOVING AND INSTALLING .
Nut
- 21 Nm
- Quantity: 2
Rear Lid Drive Unit 2 -VX77-
- Right
- With Rear Lid Motor 2 -V445- and Sensor in Rear Lid Motor 2 -G746-
- Removing and Installing. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, REMOVING AND INSTALLING .
- Programming. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, PROGRAMMING .
Mount
- Right
- With ball pin
Adjusting Buffer
- Right
- Removing and Installing. Refer to ADJUSTING BUFFER, REMOVING AND INSTALLING .
- Adjusting. Refer to HEIGHT, ADJUSTING USING ADJUSTING BUFFER .
Rear Lid Seal
- Removing and Installing. Refer to REAR LID SEAL, REMOVING AND INSTALLING .
Striker
- Removing and Installing. Refer to STRIKER, REMOVING AND INSTALLING .
- Adjusting. Refer to HEIGHT ADJUSTMENT AT STRIKER .
Bolt
- 8 Nm
- Quantity: 2
Nut
- 21 Nm
- Quantity: 2
Bolt
- 10 Nm + 90°
- Quantity: 2
- Replace after removing.
Nut
- 20 Nm + 45°
Hinge
- Right
- Removing and Installing. Refer to HINGES, REMOVING AND INSTALLING .
Closing Assist Release Cable
- Removing and Installing. Refer to CLOSING ASSIST RELEASE CABLE, REMOVING AND INSTALLING .
Nut
- 20 Nm + 45°
Bolt
- 12 Nm
- Quantity: 2
Rear Lid Latch Trim Panel
- Removing and Installing. Refer to REAR LID LOWER TRIM PANEL, REMOVING AND INSTALLING
Rear Lid Closing Assist Motor -V382-
- Removing and Installing. Refer to Rear Lid Closing Assist Motor -V382-, REMOVING AND INSTALLING .
Locking Element
- Quantity: 3
- For the closing assist
Power Rear Lid Opening Control Module -J938-
- Removing and Installing. Refer to Rear Lid Control Module -J605-, REMOVING AND INSTALLING .
Adjusting Buffer
- Left
- Removing and Installing. Refer to ADJUSTING BUFFER, REMOVING AND INSTALLING .
- Adjusting. Refer to HEIGHT, ADJUSTING USING ADJUSTING BUFFER .
Mount
- Left
- With ball pin
Rubber Grommet
- Removing and Installing. Refer to REAR LID, REMOVING AND INSTALLING .
Hinge
- Left
- Removing and Installing. Refer to HINGES, REMOVING AND INSTALLING .
Rear Lid Drive Unit -VX69-
- Left
- With Rear Lid Motor 1 -V444- and Sensor in Rear Lid Motor 1 -G745-
- Removing and Installing. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, REMOVING AND INSTALLING .
- Programming. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, PROGRAMMING .
Bolt
- 10 Nm + 90°
- Quantity: 2
- Replace after removing.
Cover
- No replacement part
Mount
- Right
- With ball pin