LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2018 >> A6 Premium Plus >> Repair and Diagnosis >> External Pages >> Different car >> Section 132 (Hybrid Control System (Diagnostic Codes (P0A92-261 - P0C41-627))) >> Hybrid Control System >> DTC P0A92-521: Hybrid Generator Performance [08/2013 - ] >> Procedure

DTC P0A92-521: Hybrid Generator Performance [08/2013 - ]: Procedure

WARNING: This page is about a different car, the 2014 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check for DTCs.

      Result

      Result Proceed to
      P0A92-521 only is output, or DTCs except the ones in the table below are also output. A
      Any of the following DTCs are also output. B
      DTC No. Relevant Diagnosis
      P0A1A (all INF codes)*1 Generator Control Module
      P0A1B (all INF codes)*1 Drive Motor "A" Control Module
      P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
      P0A3F-243 Drive Motor "A" Position Sensor Circuit
      P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
      P0A41-245 Drive Motor "A" Position Sensor Circuit Low
      P0A4B-253 Generator Position Sensor Circuit
      P0A4C-513 Generator Position Sensor Circuit Range/Performance
      P0A4D-255 Generator Position Sensor Circuit Low
      P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
      P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
      P0A72 (all INF codes)*1 Generator Phase V Current
      P0A75 (all INF codes)*1 Generator Phase W Current
      P0A78-266, 267, 279, 287, 503, 504, 505, 506, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
      P0A7A-203, 325, 517, 518, 809, 810, 811 Generator Inverter Performance
      P0A94-547, 548, 549, 554, 555, 556, 585, 587, 589, 590 DC / DC Converter Performance
      P0AA6 (all INF codes)*1 Hybrid Battery Voltage System Isolation Fault
      P0C76-523 Hybrid Battery System Discharge Time Too Long
      P3004-132 High Voltage Power Resource

      HINT: 

      • *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
      • P0A92-521 may be stored due to a malfunction which causes the DTCs in the preceding table to be stored. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a reproduction test to check that no DTCs are output.
    5. Turn the power switch off.

    B → See step   12 

    A: Go to next step 

  2. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check for DTCs.

      Result

      Result Proceed to
      Any of the following DTCs are also output. A
      P0A92-521 only is output, or DTCs except the ones in the table below are also output. B
      DTC No. Relevant Diagnosis
      P0A78-306 Drive Motor "A" Inverter Performance
      P0A90-251, 509 Drive Motor "A" Performance

      HINT: 

      When the DTCs listed in the preceding table are also output, there may be a short between the HSDN (MG shut down signal) circuit and power circuit.

    5. Turn the power switch off.

    B → See step   4 

    A: Go to next step 

  3. CHECK POWER MANAGEMENT CONTROL ECU. Refer to  PROCEDURE - Step 3 

    NG → See step   9 

    OK: Go to next step 

  4. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR). Refer to  PROCEDURE - Step 4 

    NG → CONNECT SECURELY 

    OK: Go to next step 

  5. CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION). Refer to  PROCEDURE - Step 9 

    B → REPLACE MALFUNCTIONING PARTS 

    C → CONNECT SECURELY 

    A: Go to next step 

  6. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1). Refer to  PROCEDURE - Step 11 

    NG → See step   7 

    OK → See step   11 

  7. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION). Refer to  PROCEDURE - Step 26 

    B → REPLACE MALFUNCTIONING PARTS 

    C → CONNECT SECURELY 

    A: Go to next step 

  8. CHECK GENERATOR CABLE. Refer to  PROCEDURE - Step 27 

    NG → See step   14 

    OK → See step   13 

  9. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY). Refer to  PROCEDURE - Step 4 

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  10. CHECK INVERTER WITH CONVERTER ASSEMBLY. Refer to  PROCEDURE - Step 5 

    NG → See step   11 

    OK → See step   15 

  11. REPLACE INVERTER WITH CONVERTER ASSEMBLY. Refer to  COMPONENTS [08/2013 - ] 
  12. GO TO DTC CHART (HYBRID CONTROL SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2013 - ] 
  13. REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY. Refer to  COMPONENTS [08/2013 - ] 
  14. REPLACE GENERATOR CABLE. Refer to  COMPONENTS [08/2013 - ] 
  15. REPLACE POWER MANAGEMENT CONTROL ECU. Refer to  COMPONENTS [08/2013 - ] 
scientia non olet · About LEMON Manuals