Rearview Camera -R189-, CALIBRATING

-- Establish the requirements. Refer to Calibration Requirements .

-- Connect the Vehicle Diagnostic Tester.

Calibration Tool - Wheel Center Mountings: VAS6350/1  Installing

-- Check which hole circle the rims have.

-- Equip the Calibration Tool - Wheel Center Mountings: VAS6350/1  appropriately.

-- To do so, secure three wheel bolt adapters in the hole circle to each Calibration Tool - Wheel Center Mountings: VAS6350/1  .

-- Place the paddle on both Calibration Tool - Wheel Center Mountings: VAS6350/1  and secure them using a clamping screw.

-- Place the Calibration Tool - Wheel Center Mountings: VAS6350/1  onto the wheel bolts on the rear wheels.

The Calibration Tool - Wheel Center Mountings: VAS6350/1  are positioned by the "O-rings" in the adapters and secured.

-- Adjust the paddles with aid of lock bolts so that they move freely just above the floor. Check the paddles for ease of movement.

-- Install and align the Calibration Tool: VAS6350  . Refer to Calibration Tool .

Distance Measurement

-- Switch on the Calibration Tool - Spacing Laser: VAS6350/2  .

The following display appears.

The display shows how to stop the Calibration Tool - Spacing Laser: VAS6350/2  . Press the corresponding button.

1. Attach with Front Edge
2. Attach with Rear Edge

-- Hold the Calibration Tool - Spacing Laser: VAS6350/2  -2- flush in the bracket on one side of the calibration board as illustrated. The Calibration Tool - Spacing Laser: VAS6350/2  -2- must sit securely on the bracket at the same time.

-- Push the measurement button briefly.

The laser switches on.

The laser beam from the Calibration Tool - Spacing Laser: VAS6350/2  -2- must hit the lower, enlarged section of the paddle -1-.

If this is not the case, the paddles must be corrected accordingly via clamping screws on the Calibration Tool - Wheel Center Mountings: VAS6350/1  .

-- Use one hand to secure the Calibration Tool - Spacing Laser: VAS6350/2  in the bracket on the Calibration Tool: VAS6350  while the laser beam is visible on the paddle.

-- Then press the measurement button for the distance measurement briefly.

-- Write down the value.

-- Repeat this measurement on the other side of the Calibration Tool: VAS6350  in the same way for the rear wheel.

The distance value must be the same on both sides.

If values are not identical:

-- Align the Calibration Tool: VAS6350  long enough so that both sides are identical.

-- When adjusting, make sure the Calibration Tool - Linear Laser: VAS6350/3A  strikes the center above the Audi rings and that the level indicator remains centered. Adjust if necessary.

Distance Measurement -H-

-- Measure the height of the Calibration Tool: VAS6350  , dimension -H- (top edge platform - floor).

Make sure the Calibration Tool - Spacing Laser: VAS6350/2  is adjusted correctly (attach with front edge).

The display shows how to stop the Calibration Tool - Spacing Laser: VAS6350/2  . Press the corresponding button.

1. Attach with Front Edge
2. Attach with Rear Edge

Enter the height and distance dimensions into the Vehicle Diagnostic Tester in "millimeters".

Performing Calibration

The Vehicle Diagnostic Tester is attached.

-- Select the Diagnostic  mode and start the diagnostic.

-- Select the test plan  tab.

-- Select the Select individual tests  button and choose the following sequence.

• Body
• Electrical Equipment
• 01 - OBD-capable systems
• 6C - Rearview camera system control module - J772
• 6C - Rearview camera system control module, functions
• 6C - Calibrating

From here, the Vehicle Diagnostic Tester advances the calibration procedure forward.