Camshafts, Removing, Used Camshafts, Reinstalling On Cylinder Bank 1 (Right): Installing

Fig 1: Identifying Camshaft Fitting Tool

Courtesy of AUDI OF AMERICA, LLC

• Secure crankshaft in "TDC" position using Crankshaft Holder 3242.

-- Mount the Camshaft Fitting Tool - T40096 onto the teeth of the intake camshaft so that one arm of the clamping tool engages in one sprocket half.

• The wider arm must engage into the wider half of the sprocket.

-- Tension the tensioning tool with the thumb wheel until the tooth faces align.

-- Lay the camshafts and the camshaft bearings that are tied up with cable ties -arrows- onto the cylinder head.

Fig 2: Identifying Cable Ties

Courtesy of AUDI OF AMERICA, LLC

-- Check the camshaft "TDC" position:

Fig 3: Identifying Intake Camshaft And Exhaust Camshaft

Courtesy of AUDI OF AMERICA, LLC

• The intake camshaft -1- must be able to be stopped with the Camshaft Adjustment Pins T40060.
• The bolt -arrow- in the Camshaft Adjustment Pins T40060 must be perpendicular to the center axis of the camshaft.
• The exhaust camshaft -2- must be positioned so that the groove -arrow A- runs parallel above the joint -arrow B- between the thrust bearing and the bearing cap.

-- Remove the Camshaft Adjustment Pins T40060.

Fig 4: Identifying Camshaft Chain Sprocket Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Screw in two camshaft chain sprocket bolts with five turns each into the threaded openings of the camshaft as shown in the illustration.

-- Attach the Counterhold - Kit - Multiple Use T10172 with the Counterhold - Kit - Adapter 5 T10172/5 to both of the bolts and turn the camshafts approximately 30° counterclockwise -arrow- until the groove -arrow A- in the camshaft points vertically towards the cylinder head sealing surfaces -arrows B-.

Fig 5: Identifying Counterhold - Kit - Multiple Use With Adapter

Courtesy of AUDI OF AMERICA, LLC

-- Check the installed location of the alignment sleeves:

Fig 6: Identifying Alignment Sleeves

Courtesy of AUDI OF AMERICA, LLC

• Both alignment sleeves -arrows- must be inserted into the openings on the thrust bearing "IV".
• The alignment sleeves must engage in the openings in the cylinder head.

-- Install the bolts -1 to 12- in the bearing cap.

Fig 7: Cylinder Bank 1 (Right) Bearing Cap - Tightening Specification and Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Install the Locking Device T40311 on the mounting bracket -arrows- for the tension claws, as shown in the illustration.

Fig 8: Identifying Locking Device T40311

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bearing cap bolts, refer to Figure.

Fig 9: Cylinder Bank 1 (Right) Bearing Cap - Tightening Specification and Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Remove the Locking Device T40311.

-- Attach the Counterhold - Kit - Multiple Use T10172 and the Counterhold - Kit - Adapter 5 T10172/5 to both of the bolts and turn the camshafts approximately 30° clockwise -arrow- until the groove -arrow A- in the camshaft is above the opening -arrow B- for the Camshaft Adjustment Pins T40060.

Fig 10: Identifying Counterhold - Kit - Multiple Use And Adapter

Courtesy of AUDI OF AMERICA, LLC

-- Check the camshaft "TDC" position:

Fig 11: Identifying Intake Camshaft And Exhaust Camshaft

Courtesy of AUDI OF AMERICA, LLC

• The intake camshaft -1- must be able to be stopped with the Camshaft Adjustment Pins T40060.
• The bolt -arrow- in the Camshaft Adjustment Pins T40060 must be perpendicular to the center axis of the camshaft.
• The exhaust camshaft -2- must be positioned so that the groove -arrow A- runs parallel above the joint -arrow B- between the thrust bearing and the bearing cap.

Install in reverse order of removal. Note the following:

-- Remove the Camshaft Fitting Tool - T40096.

-- Install the camshaft timing chains, refer to Installing .