Camshafts Or Camshaft Bearing, Removing And Replacing On Cylinder Bank 2 (Left): Installing

Fig 1: Identifying Camshaft Fitting Tool

Courtesy of AUDI OF AMERICA, LLC

• Secure crankshaft in "TDC" position using Crankshaft Holder 3242.

-- Mount the Camshaft Fitting Tool - T40096 onto the teeth of the intake camshaft so that one arm of the clamping tool engages in one sprocket half.

• The wider arm must engage into the wider half of the sprocket.

-- Tension the tensioning tool with the thumb wheel until the tooth faces align.

The camshaft thrust bearings and the bearing cap for cylinder bank 2 are marked after work is performed on the exhaust side to prevent them from being installed incorrectly:

Fig 2: Identifying Camshaft Thrust Bearings And Bearing Cap For Cylinder Bank 2

Courtesy of AUDI OF AMERICA, LLC

-- Lay the camshafts thrust bearings "I, II, III" on the cylinder head.

Fig 3: Identifying Thrust Bearing Oil Channels

Courtesy of AUDI OF AMERICA, LLC

• The cylinder head oil openings -arrow 1- must flow into the thrust bearing oil channels -arrow 2-.

-- Lay the camshaft thrust bearing "IV" on the cylinder head.

Fig 4: Identifying Alignment Sleeves

Courtesy of AUDI OF AMERICA, LLC

• Both alignment sleeves -arrows- must be inserted into the openings on the thrust bearing.
• The alignment sleeves must engage in the openings in the cylinder head.

-- Check the installation direction of the thrust bearings:

Fig 5: Identifying Round Edge And Cornered Edge

Courtesy of AUDI OF AMERICA, LLC

• The round edge -arrow 2- points towards the intake side.
• The cornered edge -arrow 1- points towards the exhaust side.

-- Place the camshafts in the "TDC" position in the thrust bearings.

Fig 6: Identifying Intake Camshaft And Exhaust Camshaft

Courtesy of AUDI OF AMERICA, LLC

• The intake camshaft -2- must be able to be stopped with the Camshaft Adjustment Pins T40060.
• The bolt -arrow- in the Camshaft Adjustment Pins T40060 must be perpendicular to the center axis of the camshaft.
• The exhaust camshaft -1- must be positioned so that the groove -arrow A- runs parallel above the joint -arrow B- between the thrust bearing and the bearing cap.

-- Apply the appropriate bearing cap to the corresponding thrust bearing.

-- Loop a cable tie -arrows- on the right and left around the thrust bearing and the bearing cap and tighten them.

Fig 7: Identifying Cable Ties

Courtesy of AUDI OF AMERICA, LLC

-- Install the bolts -1 to 12- in the bearing cap.

Fig 8: Cylinder Bank 2 (Left) Bearing Cap - Tightening Specification and Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Install the Locking Device-Locking Pin T40311/1 in the threaded hole -1- at the level of the 5-cylinder, as shown in the illustration.

Fig 9: Identifying Locking Device-Locking Pin

Courtesy of AUDI OF AMERICA, LLC

-- Install the Locking Device T40311 on the mounting bracket -arrows- for the tension claws, as shown in the illustration.

-- Tighten the bearing cap bolts, refer to Figure.

Fig 10: Cylinder Bank 2 (Left) Bearing Cap - Tightening Specification and Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Remove the Locking Device T40311 and the Locking Device-Locking Pin T40311/1.

-- Check the camshaft "TDC" position:

Fig 11: Identifying Intake Camshaft And Exhaust Camshaft

Courtesy of AUDI OF AMERICA, LLC

• The intake camshaft -2- must be able to be stopped with the Camshaft Adjustment Pins T40060.
• The bolt -arrow- in the Camshaft Adjustment Pins T40060 must be perpendicular to the center axis of the camshaft.
• The exhaust camshaft -1- must be positioned so that the groove -arrow A- runs parallel above the joint -arrow B- between the thrust bearing and the bearing cap.

Install in reverse order of removal. Note the following:

-- Remove the Camshaft Fitting Tool - T40096.

-- Install the camshaft timing chains, refer to Installing .