Overview - Drive Axle With Outer CV Joint With 100 Mm Diameter And Inner CV Joint With 108 Mm Diameter: Notes
WARNING: This page does not describe the selected car, but rather 18 other vehicles, including the 2016 Audi S4, 2016 Audi A4 Quattro, 2016 Audi A4, 2015 Audi S4, and 2015 Audi A4 Quattro. However, it is still accessible from the selected car via links, so may be relevant.
- Cover
- Remove the cover carefully using a drift
- Always replace.
- The adhesive surfaces on the cover/inner CV joint must be free of grease when installing.
- Before mounting on the CV joint, coat the sealing surface with Sealant. Refer to INSTALLING A 100 MM DIAMETER OR 108 MM DIAMETER INNER CV JOINT (Figure).
- Locking Ring
- Remove and install using commercially available locking ring pliers.
- Always replace.
- Inner CV Joint
- Outer diameter: 108 mm
- Replace only as complete unit.
- Checking. Refer to INNER CV JOINT, CHECKING .
- Removing. Refer to REMOVING A 100 MM DIAMETER OR 108 MM DIAMETER INNER CV JOINT .
- Installing. Refer to INSTALLING A 100 MM DIAMETER OR 108 MM DIAMETER INNER CV JOINT .
- Grease quantity and type. Refer to GREASE QUANTITY AND TYPE (100MM & 108 MM) or GREASE QUANTITY AND TYPE (88MM & 100MM) .
- Adhesive surface must be free of oil and grease
- When installing joint on axle shaft, splines on axle shaft must be lightly coated with grease used in joint.
- Locking Plate
- Bolt
- 70 Nm
- Always replace if removed
- Clamp
- Always replace.
- Tensioning. Refer to INSTALLING A CLAMP ON THE INNER JOINT AND CLAMPING (See Figure).
- Inner CV Joint Protective Boot
- Without vent hole
- Check the inner CV joint if damaged. Refer to INNER CV JOINT, CHECKING .
- The protective boot/drive shaft sealing surfaces must be free of grease when installing.
- Before tightening clamp, briefly raise CV boot to allow pressure to equalize.
- Clamp
- Always replace.
- Tensioning. Refer to INSTALLING A CLAMP ON THE INNER JOINT AND CLAMPING (See Figure).
- Drive Axle
- Removing and installing. Refer to DRIVE AXLE, REMOVING AND INSTALLING .
- CV Boot for Outer CV Joint
- Without vent hole
- Check for tears and chafing; replace if necessary
- Check the outer CV joint if damaged. Refer to OUTER CV JOINT, CHECKING .
- The protective boot/outer CV joint sealing surfaces must be free of grease when installing.
- Before tightening clamp, briefly raise CV boot to allow pressure to equalize.
- Clamp
- Opening. Refer to "Open The Clamp Using Pliers 3340 " in DRIVE AXLE, DISASSEMBLING AND ASSEMBLING, DRIVE AXLE WITH 88 MM OR 100 MM DIAMETER CV JOINT (See Figure).
- Tensioning. Refer to INSTALLING CLAMP ON 88 MM OR 100 MM DIAMETER OUTER JOINT .
- Locking Ring
- Always replace.
- Insert into ring groove of shaft before installation (not visible on installed joint)
- Before installing CV joint, align the sealing ring in center with opening facing upward.
- Outer CV Joint
- Outer diameter: 100 mm
- Replace only as complete unit.
- Checking. Refer to OUTER CV JOINT, CHECKING .
- Removing. Refer to DRIVE AXLE, DISASSEMBLING AND ASSEMBLING, DRIVE AXLE WITH 88 MM OR 100 MM DIAMETER CV JOINT .
- Installing: Drive onto shaft with plastic mallet until the compressed circlip seats.
- Circlip must lie in joint chamfer when guiding in, guide with pliers if necessary.
- Grease quantity and type. Refer to GREASE QUANTITY AND TYPE (100MM & 108MM) .
- The protective boot/outer CV joint sealing surfaces must be free of grease when installing.
- When installing joint on axle shaft, splines on axle shaft must be lightly coated with grease used in joint.
- Bolt
- 200 Nm +180°
- Always replace.
- Follow the assembly information when loosening and tightening. Refer to DRIVE AXLE THREADED CONNECTION, LOOSENING AND TIGHTENING .