Right Side Of The Engine Compartment

WARNING: This page is about a different car, the 2012 Audi S5, 2011 Audi S5, 2010 Audi S5, 2009 Audi S5, and 2008 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Component Location Overview (Right Side Of Engine Compartment)

Courtesy of AUDI OF AMERICA, LLC

1 - Mass Air Flow (MAF) Sensor -G70- /Intake Air Temperature (IAT) Sensor -G42-
- Removing and installing, refer to MASS AIR FLOW SENSOR .
2 - Camshaft Adjustment Valve 1 (exhaust) -N318-
- 2.4 Nm
3 - Electrical Connectors For
- Heated Oxygen Sensor (HO2S) -G39- before catalytic converter with Oxygen Sensor (O2S) Heater -Z19-
- Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) -G130- with Oxygen Sensor (O2S) 1 (behind Three Way Catalytic Converter (TWC)) Heater -Z29-
- Component location, refer to Figure
4 - Camshaft Adjustment Valve 1 -N205-
- Component location, refer to Figure
- 2.4 Nm
5 - Throttle Valve Control Module -J338- connector
6 - Throttle Valve Control Module -J338-
- After replacing the Throttle Valve Control Module -J338-, select "adapt throttle valve control module" in "Guided Functions".
7 - Knock Sensor (KS) 2 -G66-
- Component location, refer to Figure
- Electrical harness connector, refer to Figure
- Removing and installing, refer to KNOCK SENSORS
- 20 Nm
8 - Fuel Pressure Sensor -G247-
- Component location, refer to Figure
- Removing and installing, refer to FUEL PRESSURE SENSOR
- 25 Nm
- Coat the thread with clean oil
9 - Knock Sensor (KS) 1 -G61-
- Component location, refer to Figure
- Electrical harness connector, refer to Figure
- Removing and installing, refer to KNOCK SENSORS
- 20 Nm
10 - Components on front of engine
- Locations, refer to Figure
- Intake Flap Motor -V157-
- Beginning with MY 2009, the Variable Intake Manifold Runner Motor -V157- has become the Intake Manifold Tuning Valve -N316-
- Intake Manifold Runner Position Sensor -G336-
- Variable Intake Manifold Runner Motor -V183-
- Beginning with MY 2009, the Variable Intake Manifold Runner Motor -V183- has become the Intake Manifold Tuning Valve -N156-
- Intake Manifold Runner Position Sensor 2 -G512-
- Electrical connector from Knock Sensor (KS) 4 -G199-
- Electrical connector from Knock Sensor (KS) 3 -G198-
- Electrical connector from Knock Sensor (KS) 1 -G61-
- Electrical connector from Knock Sensor (KS) 2 -G66-
- Oil Pressure Switch -F1- for checking removing and installing, refer to appropriate service information.
11 - Camshaft Position (CMP) sensor -G40-
- Component location, refer to Figure
- Removing and installing, refer to CAMSHAFT POSITION SENSOR
- 10 Nm
12 - Fuel Metering Valve -N290-
- Component location, refer to Figure
13 - High Pressure Pump
- With Fuel Metering Valve -N290-
- Component location, refer to Figure
- Removing and installing, refer to HIGH PRESSURE PUMP
14 - Ignition Coils, Cylinder Bank 1
- Ignition Coil 1 with Power Output Stage -N70-
- Ignition Coil 2 with Power Output Stage -N127-
- Ignition Coil 3 with Power Output Stage -N291-
- Ignition Coil 4 with Power Output Stage -N292-
- Removing and installing, refer to IGNITION COILS
15 - Camshaft Position (CMP) Sensor 3 -G300-
- Attached to outside of cylinder head
- Component location, refer to Figure
- Removing and installing, refer to CAMSHAFT POSITION SENSOR
- 10 Nm
16 - Secondary Air Injection (AIR) Pump Motor -V101-
- Component location, refer to Figure
- Removing and installing, refer to appropriate service information.
17 - Intake Air Switch-Over Valve -N335-
- Component location, refer to Figure