Camshafts Or Camshaft Bearing, Removing And Installing For Cylinder Bank 1, Right: Installing

Fig 1: Crankshaft Holder 3242

Courtesy of AUDI OF AMERICA, LLC

• Tightening specifications, refer to OVERVIEW - VALVETRAIN .
• Secure crankshaft -1- in "TDC" position using Locking Pin For Crankshaft T40237.

-- Mount the Camshaft Fitting Tool - T40096 T40096 onto the teeth of the intake camshaft so that one arm of the clamping tool engages in one sprocket half.

Fig 2: Identifying Camshaft Fitting Tool

Courtesy of AUDI OF AMERICA, LLC

• The wider arm must engage into the wider half of the sprocket.

-- Tension the tensioning tool with the thumb wheel until the tooth faces align.

The camshaft thrust bearings and the bearing cap for cylinder bank 1 are marked after work is performed on the exhaust side to prevent them from being installed incorrectly:

Fig 3: Identifying Camshaft Thrust Bearings And Bearing Caps For Cylinder Bank 1

Courtesy of AUDI OF AMERICA, LLC

-- Lay the camshafts thrust bearings "I, II, III" on the cylinder head.

Fig 4: Identifying Thrust Bearing Oil Channels

Courtesy of AUDI OF AMERICA, LLC

• The cylinder head oil openings -arrow 1- must flow into the thrust bearing oil channels -arrow 2-.

-- Lay the camshaft thrust bearing "IV" on the cylinder head.

Fig 5: Identifying Alignment Sleeves

Courtesy of AUDI OF AMERICA, LLC

• Both alignment sleeves -arrows- must be inserted into the openings on the thrust bearing.
• The alignment sleeves must engage in the openings in the cylinder head.

-- Check the installation direction of the thrust bearings:

Fig 6: Identifying Round Edge And Cornered Edge

Courtesy of AUDI OF AMERICA, LLC

• The round edge -arrow 2- points towards the intake side.
• The cornered edge -arrow 1- points towards the exhaust side.

-- Place the camshafts in the "TDC" position in the thrust bearings.

Fig 7: Identifying Intake Camshaft And Exhaust Camshaft

Courtesy of AUDI OF AMERICA, LLC

• The intake camshaft -1- must be able to be stopped with the Camshaft Adjustment Pins T40060.
• The bolt -arrow- in the Camshaft Adjustment Pins T40060 must be perpendicular to the center axis of the camshaft.
• The exhaust camshaft -2- must be positioned so that the groove -arrow A- runs parallel above the joint -arrow B- between the thrust bearing and the bearing cap.

-- Apply the appropriate bearing cap to the corresponding thrust bearing.

-- Loop a cable tie -arrows- on the right and left around the thrust bearing and the bearing cap and tighten them.

Fig 8: Identifying Cable Ties

Courtesy of AUDI OF AMERICA, LLC

-- Remove the Camshaft Adjustment Pins T40060.

Fig 9: Identifying Camshaft Chain Sprocket Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Screw in two camshaft chain sprocket bolts with five turns each into the threaded openings of the camshaft as shown in the illustration.

-- Attach the Counterhold - Kit - Multiple Use T10172 with the Counterhold - Kit - Adapters 5-9 T10172/5 to both of the bolts and turn the camshafts approximately 30° counterclockwise -arrow- until the groove -arrow A- in the camshaft points vertically towards the cylinder head sealing surfaces -arrows B-.

Fig 10: Identifying Counterhold - Kit - Multiple Use With Adapter

Courtesy of AUDI OF AMERICA, LLC

-- Install the bolts -1 to 12- in the bearing cap.

Fig 11: Cylinder Bank 1 (Right) Bearing Cap - Loosening And Tightening Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Install the Dial Gauge T40311 on the mounting bracket -arrows- for the tension claws, as shown in the illustration.

Fig 12: Identifying Locking Device T40311

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bearing cap bolts, refer to Figure.

Fig 13: Cylinder Bank 1 (Right) Bearing Cap - Loosening And Tightening Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Attach the Counterhold - Kit - Multiple Use T10172 and the Counterhold - Kit - Adapters 5-9 T10172/5 to both of the bolts and turn the camshafts approximately 30° clockwise -arrow- until the groove -arrow A- in the camshaft is above the opening -arrow B- for the Camshaft Adjustment Pins T40060.

Fig 14: Identifying Counterhold - Kit - Multiple Use And Adapter

Courtesy of AUDI OF AMERICA, LLC

-- Check the camshaft "TDC" position:

Fig 15: Identifying Intake Camshaft And Exhaust Camshaft

Courtesy of AUDI OF AMERICA, LLC

• The intake camshaft -1- must be able to be stopped with the Camshaft Adjustment Pins T40060.
• The bolt -arrow- in the Camshaft Adjustment Pins T40060 must be perpendicular to the center axis of the camshaft.
• The exhaust camshaft -2- must be positioned so that the groove -arrow A- runs parallel above the joint -arrow B- between the thrust bearing and the bearing cap.

The rest of the installation is performed in reverse order of removal, noting the following:

-- Remove the Camshaft Fitting Tool - T40096 T40096.

-- Install the camshaft timing chains, refer to CAMSHAFT TIMING CHAIN, REMOVING FROM CAMSHAFTS .