Transmission, Installing: Notes

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2012 Audi S5, 2011 Audi S5, 2010 Audi S5, 2010 Audi A5, and 2009 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Ring Spanner Insert AF16 V.A.G 1332/14
Transportation Lock T40170

Procedure

NOTE:

Replace bolts that are tightened to the specification.

Replace self-locking nuts and bolts and seals, gaskets and O-rings.

Secure all hose connections with hose clamps of the same type as those equipped by the factory.

When installing, bring all cable ties back to same positions.

Transmission Installation Tightening Specifications: TRANSMISSION, INSTALLING

-- Before installing a replacement transmission, always clean out the ATF cooler and ATF pipes using compressed air (maximum 10 bar). Refer to AUTOMATIC TRANSMISSION FLUID LINES, CLEANING .

-- Clean residue from the threaded holes in the cylinder block using a thread tap before installing.

-- When installing a replacement transmission, install the transmission support, the transmission mounting and the tunnel crossmember on the new transmission. Refer to TUNNEL CROSSMEMBER, TRANSMISSION MOUNT AND TRANSMISSION SUPPORT OVERVIEW .

-- Mount the transmission onto the T40173 and secure it using the tension strap -1- as illustrated.

Fig 1: Mounting Transmission Onto T40173 And Secure It Using Tension Strap

Courtesy of AUDI OF AMERICA, LLC

-- The following preparations must be made before connecting the engine and transmission:

Fig 2: Locating Hole Next To Notch

Courtesy of AUDI OF AMERICA, LLC

-- Turn the torque converter so that hole next to the notch -arrow- is visible in the lower cut-out in the transmission housing as illustrated.

NOTE:

There is only 1 notch on the circumference; rotate the torque converter as needed.

-- Insert the T40170 in the transmission housing from below and secure it on the flange shaft -1-.

Fig 3: Identifying Transportation Lock T40170

Courtesy of AUDI OF AMERICA, LLC

-- Check if the alignment sleeves -A- for centering the engine/transmission are in the cylinder block and insert them if they are not.

Fig 4: Checking If Alignment Sleeves -A- For Centering Engine/Transmission Are In Cylinder Block

Courtesy of AUDI OF AMERICA, LLC

-- Inspect the aluminum bolts used to connect the engine to the transmission to see if they can be used again and mark them, if necessary TRANSMISSION, INSTALLING .

-- Attach the transmission to the engine and the tighten the bolts -1 and 6 through 11-.

-- Remove the T40170.

-- Clip the locking piece -1- into the starter opening.

Fig 5: Identifying Locking Piece

Courtesy of AUDI OF AMERICA, LLC

The locking piece -1- must be installed so that it fits correctly -arrows-.

NOTE:

There are different versions of the locking piece depending on the engine.

Apply some grease to the locking piece if it is difficult to install the starter.

-- Install the starter. Refer to STARTER, REMOVING AND INSTALLING .

-- Loosen the 10 - 222 A /11.

Fig 6: Identifying Additional Engine Support Bridge 10 - 222 A

Courtesy of AUDI OF AMERICA, LLC

-- Raise the transmission and tighten the tunnel crossmember bolts -arrows-. Refer to TUNNEL CROSSMEMBER, TRANSMISSION MOUNT AND TRANSMISSION SUPPORT OVERVIEW .

Fig 7: Identifying Tunnel Crossmember

Courtesy of AUDI OF AMERICA, LLC

-- Loosen the tension strap and remove the V.A.G 1383 A with the T40173 from under the transmission.

NOTE:

The following step is necessary to make sure the torque converter rests on the drive plate evenly and is not tilted.

-- Press the torque converter -2- against the drive plate -3- slightly in the direction of the -arrow- using an assembly lever -1-.

Fig 8: Pressing Torque Converter

Courtesy of AUDI OF AMERICA, LLC

-- Attach the torque converter to the drive plate as follows:

NOTE:

Use the V.A.G 1332/14 to tighten.

-- Install the first bolt -arrow- and tighten by hand (2 Nm).

Fig 9: Identifying Clutch Module First Bolt Installation Location

Courtesy of AUDI OF AMERICA, LLC

-- Insert the T40058 guide pins as follows:

Fig 10: Identifying Guide Pin And Adapter T40058

Courtesy of AUDI OF AMERICA, LLC

The large diameter -arrow 1- faces the engine.
The small diameter -arrow 2- faces the adapter.

-- Continue turning the crankshaft 180° in the direction of the engine rotation using the T40058 -arrow-.

Fig 11: Identifying Torque Converter Bolts And Adapter T40058

Courtesy of AUDI OF AMERICA, LLC

-- With the crankshaft in this position, tighten the bolt -arrow- to 60 Nm.

Fig 12: Identifying Clutch Module First Bolt Installation Location

Courtesy of AUDI OF AMERICA, LLC

-- Continue turning the crankshaft 60° and tighten the remaining 5 bolts to the tightening specification.

-- Tighten the remaining bolts -2 through 5-.

Fig 13: Tightening Remaining Bolts -2 Through 5-

Courtesy of AUDI OF AMERICA, LLC

Install in reverse order of removal paying attention to the following:

Fig 14: Pressing CV Joint Off Steering Gear And Sliding It Up

Courtesy of AUDI OF AMERICA, LLC

-- Attach the steering column to the steering gear. Refer to STEERING COLUMN .

-- Install the subframe crossbrace. Refer to SUBFRAME CROSSBRACE, REMOVING AND INSTALLING .

-- Install selector lever cable. Refer to SELECTOR LEVER CABLE .

-- Install the ATF pipes. Refer to AUTOMATIC TRANSMISSION FLUID COOLER AND LINES OVERVIEW .

-- Attach the left and right drive axles to the transmission flange shafts. Refer to 40 FRONT SUSPENSION .

-- Install the driveshaft heat shield TRANSMISSION, INSTALLING => Driveshaft Heat Shield - Tightening Specification .

-- Install the driveshaft. Refer to Removal and Installation or Removal and Installation .

-- Reconnect exhaust system making sure it is not under stress. Refer to [For engine(s) CALA] Exhaust System, Emission Controls .

-- Install the noise insulation. Refer to NOISE INSULATION .

-- Connect the battery. Refer to BATTERY, DISCONNECTING AND CONNECTING .

CAUTION:

There is a risk of destroying control modules with excess voltage.

Do not use a charger as a starting aid.

-- Check the selector lever cable and adjust if necessary. Refer to SELECTOR LEVER CABLE, ADJUSTING .

-- Check the ATF level and correct if necessary. Refer to ATF, CHECKING LEVEL AND CORRECTING .

Tightening specifications

NOTE:

The tightening specifications apply only to lightly greased, oiled, phosphated or blackened nuts and bolts.

Additional lubricant such as engine or transmission oil may be used, but do not use graphite lubricant.

Do not use any ungreased parts.

Tightening specification tolerance: ± 15%.

Other tightening specifications:

Component		Nm
Bolts and nuts	M6	9
	M7	15
	M8	20
	M10	40
	M12	65