LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2014 >> A5 Prestige >> Repair and Diagnosis >> External Pages >> Different car >> Section 1275 (Communication (Telephone - Internet Access) (Coupe)) >> 91 Communication >> Rearview Camera System >> Rearview Camera System, Calibrating >> Calibration Tool - Lane Change Calibration Tool: Vas6350/4, Installing And Aligning >> Installed Calibration Tool : Vas6350 Overview

Installed Calibration Tool : Vas6350 Overview

WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Identifying Calibration Tool VAS6350
GWWA91-10994Courtesy of AUDI OF AMERICA, LLC
  1. Calibration Tool - Wheel Center Mountings:VAS6350/1 
  2. Calibration Tool - Wheel Center Mountings:VAS6350/1 
  3. Right angle bracket
    • Calibration Tool - Spacing Laser:VAS6350/2  mount
  4. Plastic Foot
    • Three on the Calibration Tool - Lane Change Calibration Tool:VAS6350/4  underbody
    • Can be adjusted for adjusting the horizontal position of the Calibration Tool - Lane Change Calibration Tool:VAS6350/4 
  5. Calibration Tool - Linear Laser:VAS6350/3 
    • On the Calibration Tool - Lane Change Calibration Tool:VAS6350/4 
    • Switching on and off, refer to Operating Instructions.
  6. Calibration Tool - Spacing Laser:VAS6350/2 
    • Notes on operation, refer to Operating Instructions.
  7. Level on calibration platform
    • On the Calibration Tool - Lane Change Calibration Tool:VAS6350/4 
    • for checking the horizontal position
  8. Left angle bracket
    • Calibration Tool - Spacing Laser:VAS6350/2  mount
  9. Calibration Tool - Lane Change Calibration Tool:VAS6350/4 
    • Between the angled brackets on the Calibration Tool - Lane Change Calibration Tool:VAS6350/4  and the Calibration Tool - Wheel Center Mountings:VAS6350/1  -dimension A- 1.47 m to 1.90 m

Calibration Tool - Lane Change Calibration Tool:VAS6350/4  Orientation

-- Position the Calibration Tool - Lane Change Calibration Tool:VAS6350/4  behind the vehicle at a distance of 1.47 m to 1.90 m to the rear wheels, see -dimension A- in the illustration, refer to INSTALLED CALIBRATION TOOL : VAS6350 OVERVIEW 

-- Bring the Calibration Tool:VAS6350/4  into a horizontal position.

-- To do so, twist plastic feet under Calibration Tool - Lane Change Calibration Tool:VAS6350/4  so that air bubble in level is located exactly in the center of the indicator -arrow-.

Fig 2: Identifying Bubble Level (Sight Glass) On Calibration Tool VAS 6350
GWWN94-10686Courtesy of AUDI OF AMERICA, LLC
WARNING:

Make Sure Light Does Not Reflect Off The Calibration Tool - Lane Change Calibration Tool:VAS6350/4  .

Reflections affect the Rearview Camera -R189- and may make it impossible to perform the calibration.

-- Switch on the Calibration Tool - Linear Laser:VAS6350/3  -1- on the Calibration Tool - Lane Change Calibration Tool:VAS6350/4  and align the entire Calibration Tool:VAS6350/4  , so that the laser beam points to the middle of the vehicle height above the Audi rings.

Fig 3: Switching On Line Laser VAS 6350/3
GWWA91-10995Courtesy of AUDI OF AMERICA, LLC

-- Make sure the Audi rings are centered on the rear. Adjust the laser beam as needed.

Continue calibrating the Rearview Camera -R189-, refer to Rearview Camera -R189-, CALIBRATING .

scientia non olet · About LEMON Manuals